Command-line output of sender application.
sender应用程序的命令行输出。
Command-line output of receiver application.
receiver应用程序的命令行输出。
Figure 6. Command-line output of sender application.
图6.sender应用程序的命令行输出。
Figure 7. Command-line output of receiver application.
图7.receiver应用程序的命令行输出。
Which is why we've opted to hide the command line output on a different page?
这也正是我们选择在另一个页面上隐藏命令行输出的原因。
The command - line output is very explicit, and it helps you localize which tests failed and which passed.
命令行输出结果很清楚，帮助你定位哪个测试通过哪个没有通过。
The production line output is 500-2000 pcs/10 hours, the best efficiency, the excellent rates is more then 95%.
生产线的生产量在每天10小时生产500-2000个枕头。效率高，产品优良率95%以上。
If there is no respond when the oscilloscope is turned on, it is because the line output tube is broken and caused the protection of the power part.
出现开机无反应故障，原因是行输出管击穿引起电源部分保护所至。
The precise expression for the insertion loss of the parallel coupled microstrip line output bandpass filter has been given on the basis of related mathematical models.
本文在相关数学模型的基础上，推导出平行耦合微带线和平行耦合微带线输出带通滤波器插损的精确表达式。
During energizing of the one power line output, the jetting heater and the substrate heater may be selectively actuated by selectively energizing the two enable line outputs.
当接通电源线输出时，通过选择接通两启动输出线有选择地启动此两种不同的加热器。
The article analyses the reason of retrace line which is produced by changing line output transformer of TV set and its removing method on the basic of color TV set circuit and its working principle.
本文根据彩色电视机的电路结构和工作原理，分析了更换高压包引起场逆程回扫线干扰的原因及消除该逆程回归线的方法。
Isoquant curve is a line showing all the alternative combinations of two factors that can produce a given level of output.
等产量线是表示两种生产要素的不同数量组合可以带来相等产量的一条曲线。
The first line of output in this section lists the CPU that detected the problem that caused the dump routine to be invoked (CPU 0 in the previous example).
该部分中，输出的第一行列出了检测到问题的CPU，这些问题造成转储例程被调用（在前面的示例中 CPU为 0）。
Listing 11 shows the command line and some sample output.
清单11给出命令行和一些输出示例。
Do this until you you see END! As the last line of output (see figures 9, 10 and 11).
持续这么做，直到最后一行输出是END ！为止(参见图9、10和11)。
Such a utility might equate lines to records on input, but produce multiple records per line on output.
这样一个实用程序可能将输入中的行视为记录，但是却在输出中的每行上产生多个记录。
Because the system call is displayed after it has been executed, the output is shown in the line before.
因为在其执行之后才显示这个系统调用，所以先输出了它的执行结果。
Once again, after I run this script on the command line, I see the output in Listing 14.
同样，在命令行中运行此脚本后，会看到如清单14所示的输出。
Running these commands from the command line produces output similar to the one shown in Figure 2.
从命令行中运行这些命令将产生与图 2类似的输出。
When I run this script on the command line, I see the output in Listing 12.
在命令行中运行此脚本时，输出如清单12所示。
The variant of the command being invoked is displayed in the first line of the output.
所调用的命令的变体显示在输出的第一行。
Pay special attention to the last line of the output, which gives you an indicator as to whether or not the font you are using is legally embeddable.
特别注意输出的最后一行，它告诉你关于你使用的字体嵌入是否合法的提示。
The first line of the output contains the random number of seconds selected for the sleep time, followed by the name of the script.
输出的第一行包含随机选择的睡眠秒数，然后是脚本的名称。
When you run a job in the background with default bash terminal settings, bash normally catches SIGCHLD signals and prints a message after the next terminal output line is printed.
当使用默认的bash终端设置在后台运行作业时，bash通常会捕获SIGCHLD信号并在打印下一个终端输出行之后 打印消息。
Listing 3 shows an example of the VerboseLoader command line and output, which is used to call the Run application from Listing 1.
清单3显示了VerboseLoader命令行和输出的一个例子，它用于调用清单1中的Run应用程序。
Working at the command line: input and output, pipes and streams.
在命令行下使用：输入和输出，管道和流。
You'll get 20 to 30 lines of output, one line per "device".one of the interesting lines on my computer says.
你会得到20到30行输出信息，每一行表示一个“设备(device)”。
It reformats the output of the Wireless Tools' iwlist and adds the MAC address so each client's status is summarized in one line. Its output looks like this.
它会对WirelessTools的iwlist的输出结果重新进行格式化，并添加MAC地址的信息，这样就可以在每一行中对每台客户机的状态进行总结。
The first example, written in PHP, will capture the output of the shell command "df -h," place the output into an array, and then examine each line of output against a regular expression.
采用PHP编写的第一个示例将捕获Shell命令“df—h”的输出，将输出放在一个数组中，然后根据一个正则表达式检查输出的每一行。
The mkewuid script function will output a record line for each string of characters provided on the command line.
mkewuid脚本函数为命令行上提供的每个字符串输出一个记录行。
应用推荐