Tangential continuity [C1 or G1] is the next level, defined by a circular arc creating a relatively smooth transition between these surfaces.
相切(Tangential)连续性[c 1or g 1]则是下一个层次，指的是建立一个连接这些表面间的平滑的圆弧过渡。
An arc due to an AC signal usually quenches itself as soon as the voltage level passes through zero.
交流(ac)信号产生的电弧通常在电压通过零点时就会自己熄灭。
It was reported that the overvoltage level of low resistance grounding mode is lower than that of arc suppressing coil mode, but the operation carried out the other way.
但经多年的运行，各地普遍认为小电阻接地方式比消弧线圈接地方式的过电压水平要低，但同时反映出的运行状况却存在较大差异。
On the current technical level, the double wire submerged arc narrow groove welding technology invented by Harbin welding Institute was recognized by the market.
就目前的技术水平而言，国内的哈尔滨焊接研究所的双丝埋弧窄间隙焊接技术较为被市场所认可。
In order to improve the level of automatic welding in CO_2 shielded welding, the tracking system of welding seam based on arc sensor for CO_2 shielded welding is developed in this paper.
为了提高CO_2气体保护焊的自动化水平，本文研制了用于CO_2气体保护焊的电弧传感焊缝跟踪系统。
Paper covers temporary overvoltages, second arc current, switching overvoltage, major parameters of MOA and insulation level of UHV AC apparatus.
主要内容包括：工频暂时过电压，潜供电流，操作过电压，金属氧化物避雷器主要参数，特高压电气设备的绝缘水平等。
The illinium electrode produces a slim arc when used in welding. With a high level of compression, it has a bigger melting depth in medium and high currents.
钇钨电极在焊接时弧束细长，压缩程度大，在中、大电流时其熔深比较大。
Microcomputer controlled arc welding inverter power source can raises greatly controlled level of pulse MIG welding for its flexible control, high accuracy, high system response.
采用微机控制的弧焊逆变电源控制灵活、精度高、系统响应高的特点，能够极大提高脉冲MIG焊的控制水平。
The system is ideally suited for the coned of submerged are welding with constant wire feed speed, and has increased the level of automation of the arc welding...
系统可用于等速送丝埋弧自动焊的控制，提高了焊接装备自动化水平，在微机应用于焊接领域的研究中作了进一步的探索。
The system is ideally suited for the coned of submerged are welding with constant wire feed speed, and has increased the level of automation of the arc welding process. This design is a fur- the…
系统可用于等速送丝埋弧自动焊的控制，提高了焊接装备自动化水平，在微机应用于焊接领域的研究中作了进一步的探索。
Tips: stick to the end of the cloth is level, don't post into arc, open your eyes to pull carry eye end.
Tips：贴布的尾端要呈水平，不要贴成弧形，睁眼时就能拉提眼尾。
A structure of task level OLP system is presented for arc welding robot, which consists of a modeler, a task programmer, a task planner and a robot motion simulator.
提出了一种弧焊机器人任务级离线编程系统的结构，包括建模器、任务编程器、任务规划器和机器人运动仿真器等四个基本模块。
The impaction of numerical precision on the accuracy of simulated flow field is checked. Curving level of throat wall arc mesh is compared to see the effect on flow loss.
并比较了数值精度对流场模拟精度的影响和喉道壁面网格的圆弧度处理对流动损失的影响。
Residual stress of longitudinal submerged arc welded pipe after welding is the major reason caused welded pipe stress corrosion crack, its stress level directly decide pipeline safety in service.
直缝埋弧焊管焊后残余应力是导致焊管应力腐蚀裂纹产生的主要原因。
Obstacle-free sector is a sector formed by an arc originating at the reference point of the edge of a helideck and extending outward in the horizontal plane level with the elevation of the helideck.
无障碍区域是由一个起于直升机甲板边缘的基准点并在直升机甲板的水平面向外延伸的弧形所形成的区域。
Although curves of big arc lines are higher in rate of hit its level of difficulty in techniques is higher and it is not easy to command in a short time.
弧线大的曲线虽然全中率很高，但技术难度较大，短时间内不容易掌握。
When a StreetViewPanorama first loads, by default it displays an image consisting of 25% (90 degrees of arc) of the horizontal breadth of the panorama at zoom level 1.
当一个谷歌街景图像初次载入，默认情况下，它处在缩放等级 1，这时显示了整 张全景照片 25%的水平宽度（90度的水平视野）。
The stopper auto casting and mould level control system of arc continuous caster is introduced.
介绍了炼钢厂连铸生产中的塞棒自动控制系统。
When the over-voltage is 100 ~ 150 v, the ceramic level corrosion resistance is good. Therefore, the micro-arc oxidation of Mg alloy should choose the suitable over-voltage.
并且陶瓷膜层耐蚀性在过电压为100 ~ 150V时较好，因此镁合金微弧氧化要选择适当的过电压。
When the over-voltage is 100 ~ 150 v, the ceramic level corrosion resistance is good. Therefore, the micro-arc oxidation of Mg alloy should choose the suitable over-voltage.
并且陶瓷膜层耐蚀性在过电压为100 ~ 150V时较好，因此镁合金微弧氧化要选择适当的过电压。
应用推荐