Therefore, the static mixer with large blade area had the highest mixing ratio of the process gas and air in the natural gas purification process.
因此，叶片面积大的静态混合器对天然气净化处理工艺中的过程气与空气的混合率最高。
Large aggregate makes the blade cut slower, while smaller aggregate makes the blade cut faster.
大型聚合使刀片切割速度较慢，而较小的聚合使刀片切割速度更快。
They are among the most competitive high-end standard blade market, because the standard blade often has a large inventory, interchangeable, short supply, in one or two weeks supply.
他们之间竞争最为激烈的是高档的标准刀片市场，因为标准刀片往往备有大量库存，互换性强，供货期短，可在一、二周内供货。
During shedding times, use a rubber curry and shedding blade to remove the large amounts of hair, then follow up with a vacuum.
在脱毛期，先用橡皮梳刷和褪毛刀去除大量脱落的毛发，然后再用吸尘器清理。
Experimental results show that the trajectory of particles with large mass will be close to the pressure surface of blade in the centrifugal impeller.
试验结果表明：质量大的颗粒，在离心泵叶轮中，其轨迹总是趋向叶片压力面。
Influence of each factor on blade inlet flow of a large vertical axial-flow pump is analyzed, formation mechanism of flow field in the cross section is studied.
分析各因素对大型立式轴流泵叶片进口流态的影响，研究该断面流场的形成机理。
Improvement of the physics performance of blade is obtained by reconstructing the large size surface of turbine blade based on calculation geometry.
用计算几何的方法重构大型涡轮叶片曲面，可提高叶片的物理学性能；
The impaction of long blade with high energy can cause large deformation and the blade will curl as U shape and tear the wall of the containment ring at the second impact position.
高能量长叶片撞击将形起大变形，叶片弯曲成U形，机匣在第二次撞击处被撕裂击穿。
The results show that the tip leakage flow vortex has a great effect on the blade aeroelastical stability and large tip leakage vorticity may restrain blade flutter.
计算结果表明，漏流涡对叶片气弹稳定性影响较大，大涡量的漏流涡能抑制叶片颤振发生。
The combination of the slot with an optimized blade design significantly reduces the secondary flow losses compared to the original turbine stator, especially at large negative angles of incidence.
经联合造型后的叶栅与原始叶栅相比在各个攻角下的流动损失均有大幅度降低，大负攻角下效果尤为明显。
The main advancements of manufacturing techniques in the procedure of the manufacture for large hydro turbine's blade are reviewed from the point o...
本文简要介绍从材料、毛坯、加工成型、质量控制等大型水轮机叶片制造过程中主要的技术进步。
A large, detachable plowshare with a single blade, used chiefly for breaking or clearing heavy soil.
单铧犁片，牛舌形犁：只有一个犁片的、大的，可分离式的犁铧，主要用来敲碎和清除厚土。
The blade of a large horizontal axis wind turbine is a nonlinear periodic multi-body system with fluid-rigid-flexible coupling.
大型水平轴风力发电机桨叶为流-刚-柔耦合的周期时变多体系统。
The great thing about this katana is the new large geometry blade profile. It has a profile that is larger than most blades which allows for the inexperienced cutter to cut successfully.
这把刀的亮点在于新设计的宽大的符合几何学的刀身造型，这样豪壮的设计为了能够确保缺乏练习的使用者能够成功的进行斩切。
Film cooling of the surface of a gas turbine blade was studied in a large-scale low-speed opening wind tunnel according to actual requirement of the design of aero-engine.
根据航空发动机设计的实际需要，在大尺寸低速叶栅传热风洞中对涡轮叶片表面的气膜冷却进行了综合性实验研究。
Some discussion about aerodynamic design of last stage blade of large steam turbine has been given basing on the result of S_2 design calculation.
结合长叶片级S_2流面设计问题的计算结果对大功率汽轮机长叶片气动设计进行了初步的探讨。
Plastic crusher is easy to operate, in the blade is easy, broad flat blade structure is suitable for crushing thin-walled and large volume bottles, tubes and other hard plastic.
塑料粉碎机操作方便，换刀片简便快捷，平型刀宽大的结构适合破碎大体积薄壁和瓶子、管子等硬质塑料。
Our continent is the only machinery for mold blade, designed and manufactured in one large company, product, full specifications, please call to discuss the broad masses of customers.
我公司是大陆唯一针对机械刀片模具，设计生产于一体的大型公司，产品多，规格全，欢迎广大客户来电洽谈。
The quality of the workpiece surface is subject to the side displacement of the saw blade to some large extent.
锯条的侧向位移在很大程度上决定了加工表面的质量，侧向位移过大工件表面质量得不到保证。
This paper presents the load spectrum and an engineering estimating method of the fatigue life of GRP blade of large-scale wind turbine.
研究了大型风力机玻璃钢叶片载荷谱和疲劳寿命的工程估算方法。
The machine equipped with large, medium and small die can be any of three sets of exchange, will die within the copper gear, and replacement of copper on the blade out.
本机配置有大、中、小模头三套可调换，将铜齿轮内的模头及铜板上的刀片取出更换。
The structural characteristic and machining method of runner blade servomotor piston ring for large Kaplan turbine are studied.
对大型轴流转桨式水轮机转轮接力器活塞环的结构特点及加工方法进行了研究分析。
A new design method for large cross-section blade-like ultrasonic plastic welding horns with slots is pre-sented, and relative experiments have been done to validate this method.
提出了一种大尺寸长条形超声塑焊开槽焊头的设计方法，并对其进行了实验验证。
A new design method for large cross-section blade-like ultrasonic plastic welding horns with slots is pre-sented, and relative experiments have been done to validate this method.
提出了一种大尺寸长条形超声塑焊开槽焊头的设计方法，并对其进行了实验验证。
应用推荐