The three kinds of inlet size and optional stainless steel plate out of vent panels, to meet different customer needs.
三种入风口尺寸及板型可选购不锈钢出风口面板，满足不同客户需求。
The effect of inlet size, inlet Angle, dome height, primary nozzle expansion ratio and nozzle Numbers on combustion efficiency were taken into account.
考虑了进气道尺寸、进气夹角、头部距离、一次喷嘴扩张比和喷嘴数目等结构因素对补燃室掺混与燃烧性能的影响。
The hydrodynamics of particle agglomeration flow was numerically simulated at the different inlet gas velocity, initial particle size distribution and type of agglomeration mechanisms in the absorber.
对不同入口气体速度、初始颗粒尺寸分布和不同颗粒团聚形成机理下收集器内颗粒聚团流动的流体动力特性进行数值模拟。
In a certain inlet velocities, vaneless diffusers with diffusion type have higher pressure recover coefficient and can reduce the radial size.
采取扩张型非平行壁无叶扩压器，在一定的进口速度下，可望有较高的压力恢复系数，且可以缩短径向尺寸。
It is also pointed out that the topological structure near leading edge depended on not only the gap size but also loading of cascade and thickness of inlet boundary layer.
本文指出在叶栅存在间隙时，前缘产生什么样的拓扑结构不仅取决于相对间隙的大小，同时也取决于叶栅的负荷情况。
Housing: Galvanize steel sheet material could be able to bear corrosive. Same size for the inlet and outlet can install conveniently. Connecting to the piping directly makes for installation.
外壳：采用优质热镀锌钢板制成，具有优良的耐大气腐蚀性能，进风口和出风口外形尺寸相同，可与风管直接相连，以便于安装。
Same size for the inlet and outlet can install conveniently.
进风口和出风口外形尺寸相同，以便于安装。
The effects of gap size, heat flux and inlet subcooling on the boiling incipience, flow pattern, heat transfer coefficient, flow instability and critical heat flux were analyzed and discussed.
讨论和分析了流道间隙、加热功率和入口过冷度对沸腾起始点、沸腾流态、换热系数、流动不稳定性和临界热负荷的影响。
If the grain size distribution of suspending liquid at inlet is identical, the change of inlet pressure and underflow port diameter can influence the separation efficiency.
在进料口悬浮液固相颗粒粒级分布相同的情况下，进料口压力和底流口直径的变化同样对分离效率产生影响。
This paper discussed the selection of the size(length, width and height) of the oven, the inlet mode of the hot air and the design of outlet to increase the utilization efficiency.
讨论了洞道式干燥器的长度、宽度、高度的选择，热空气进入方式和排气口的设置，以提高其热空气的利用率。
When inlet flowrates exceed a certain value, the mean oil droplet size will decrease with the inlet flowrate increasing.
提高旋流器进口油滴的平均粒径，改进旋流器的锥段结构，选择合适的入口流量都有利于提高旋流器的分离效率。
New forming process on the suction inlet of large-size electric motors as well as its raw materials dimension and mold construction is introduced.
介绍了大型电机吸风嘴成型工艺、坯料尺寸确定及模具结构。
New forming process on the suction inlet of large-size electric motors as well as its raw materials dimension and mold construction is introduced.
介绍了大型电机吸风嘴成型工艺、坯料尺寸确定及模具结构。
应用推荐