This paper studied the injection weight method, which introduced the preparation of food additives series gas standard materials of benzene in carbon dioxide.
研究了注射重量法制备食品添加剂二氧化碳中苯系列气体标准物质的实验方法。
To increase productivity, maximize on the number of cavities by using the clearance between tiebars, the platen dimensions and the injection weight of the injection moulding machine to the most.
为了提高生产效率，尽用注塑机的四柱空间、模板空间及注塑重量来达到最高的腔数。
It is clarified that the specimens of smaller mixing and injection machines were smaller variation in weight loss, sintered density and strength.
结果表明，较小的混炼机和注射机制造的试样，重量损失、烧结密度和强度的变化程度较小。
Results: The injection could attenuate abstinent syndrome of rats, restore rat weight and reduce NA, DA and 5 - ht content in brain tissue of morphine -dependent rats.
结果经参附注射液治疗的大鼠戒断症状明显减轻，体重明显恢复，脑组织中NA、DA、5-HT等单胺类神经递质水平显著降低。
Objective To evaluate the safety and availability of prophylactic treatment for venous thromboembolism by hypodermic injection of low-molecule-weight heparin (LMWH) during peri-operation period.
目的评估神经外科患者在围手术期皮下注射低分子肝素预防深静脉血栓栓塞症的安全性及有效性。
This paper presents a hardware structure-independent weight-based fault injection model for accurate emulation of the radioresistance in the SRAM-based FPGA.
提出一种与具体硬件结构无关、基于权重的错误注入模型，用于准确模拟基于SRAM的现场可编程门阵列抗辐射性能。
All data is from injection molded specimens with the exception of Drop Weight Impact.
所有数据是从注射成型用的落锤冲击异常标本。
Researches have been carried out in the second reservoir by physical modeling method to find out the formula weight of the polymer, injection rate, slug size and viscosity of the polymer solution.
通过物理模拟方法，研究杏北油田二类油层聚合物相对分子质量、注入速度、段塞大小、聚合物溶液黏度、不同注聚方式对驱油效果的影响。
When compared with each other, low-molecular-weight heparin was associated with a 32 percent reduced risk of deep vein thrombosis and a 53 percent lower rate of hematoma at the injection site.
当这两种肝素相比较时，低分子肝素能够减少32%的深静脉血栓和53%注射部位的血肿形成。
To effectively reduce the injection-machine mould-board weight, sequential optimization design method starting from high level topology optimization to low level parameter optimization was proposed.
为了有效地降低注塑机模板的重量，提出了从高层次拓扑优化到底层次参数化优化的顺序优化设计方法。
They learned that 3D printers that use heat or a laser to melt plastic consumed an estimated 50 to 100 times more electrical energy than injection molding to make an object of the same weight.
他们了解到，使用热或激光来熔化塑料三维打印机消耗的估计50至100倍的电能比注射成型，使相同的重量的目的。
Due to high water injection pressure, it is difficult to transport the logging cable into water injection WLL by its own weight during well logging process.
在注水井带压测试工艺中，由于注水压力的影响，测井电缆依靠自身质量无法向井下输送，为此开发研制了测井电缆带压下井输送器。
Objective To investigate the relationship between local compression and local hemorrhage after low molecular weight heparin (LMWH) subcutaneous injection.
目的探讨低分子肝素(LMWH)皮下注射后局部压迫与否与局部出血的关系。
The reservoir fluid takes up intermediate molecular weight components from the injection gas.
油藏流体从注入气中吸收中等分子量组分。
Conclusion: the method can be used to determine the small molecular weight impurity in the Chondroitin Sulfate injection.
结论：本方法可作为硫酸软骨素注射液小分子杂质的检测方法。
In this article the peptide chromatograms and molecular weight distribution of Cerebrolysis Injection from the EBEWE co in Austria and 8 domestic manufactures were analyzed and compared with.
本文对奥地利e BEWE公司及国内8家药厂生产的脑活素类注射液的肽色谱图及分子量分布进行分析比较。
Objective To reduce adverse reactions by way of selecting best hypodermic injection site of low molecular weight heparin sodium.
目的选择皮下注射低分子肝素钠的最佳部位，以减少由于皮下注射低分子肝素钠所引起的不良反应。
Results After intravenous and intra-abdominal injection of soaked solution of material, there were no changes in breath, appetite, body weight of mice and no death.
结果人工骨浸取液静脉及腹腔注射后不引起小鼠呼吸、进食改变或死亡，体重稳定。
Conclusion: the dose tailored to patient body weight in the injection protocol may be helpful to reduce the side effect of contrast media and the patients' complication in CTCA examination.
结论：根据体重对比剂注射方案对比剂用量少，有利于减少对比剂不良反应和并发症的发生。
It is a very important technical question whether water injection string can rely on string weight to go through the well hole or not.
注水管柱能否靠自重下放到井底是一个十分重要的技术问题。
The effect of back pressure on the weight precision in injection molding was investigated via experiments of injecting to air.
通过对空注射方式对影响精密制品质量重复精度之一的背压进行实验和理论研究。
Experimental results show that compared with open loop multi-injection speed and multi-holding pressure programmable controller controlled system, the stability of product weight has be...
实验结果表明，与程控器多级注射速度多级保压压力开环控制相比，制品重量的稳定性有明显提高。
Experimental results show that compared with open loop multi-injection speed and multi-holding pressure programmable controller controlled system, the stability of product weight has be...
实验结果表明，与程控器多级注射速度多级保压压力开环控制相比，制品重量的稳定性有明显提高。
应用推荐