Then the influence on flame structure of supersonic combustion of ratio of length and deep of cavity, obliquity of back edge of cavity and different schemes of fuel injection were studied.
用这种方法研究了不同凹腔长深比、凹腔后缘倾角和不同燃料喷注方案对超声速燃烧火焰结构的影响。
The penetration length of the core melt in sandwich injection molding was investigated by changing the viscosities of melts and process parameters.
以揭示材料粘度以及工艺参数对夹芯注塑成型过程中芯层熔体穿透深度的影响规律。
It is shown that the measured minority carrier diffusion length increases with the injection level when the latter is high.
结果表明，当注入水平较高时，少子扩散长度的测量值变长。
The structural design of the injection molds for the typical case box soda-water turnover box with strengthened ribs in length and breadth is described and analysed.
介绍一种较典型的带有纵横隔肋的箱类制品——汽水周转箱注塑模具的结构设计。
The effects of current velocity, sample volume, length and inside diameter of reaction pipe and shape on the dispersion of flow injection analysis system were in detail discussed in this paper.
本文详细地探讨和研究了载流速度、进样体积、反应管长度、内径与形状等因素对分散度的影响。
Rats induced by voix pedis subcutaneous injection with carrageenin for thrombose were also administrated for the observation of thrombus average length and recanalization rate.
大鼠足跖皮下注射角叉菜胶使尾部形成血栓后给药，观察血栓平均长度及再通率。
Finically, the dynamic property of portal water injection sheet piles is analyzed in this paper, and the influence on dynamic property of pile length and distance between piles is discussed in detail.
此外，还探讨了门架式水力插板桩的动力特性，以及桩长和桩间距对结构动力特性的影响。
It was constructed that an optimal problem for gate locations of injection molds based on the introduction of the equivalent flow length concept.
文中通过引入等效流长的概念，建立了浇口位置优化问题。
The sensitivity of capillary electrophoresis is greatly limited due to the small injection volume and the short optical path length.
由于毛细管进样体积小以及在柱检测光程短，极大地限制了毛细管电泳检测灵敏度的提高。
Conclusion: We use L as arch length and H as chord length to bend syringe needle that is used to posterior superior alveolar nerve block anesthesia by intraoral injection. The success rate is 98%.
结论：以牙槽孔至颧下嵴起始部的弧长和弦长为标准弯制注射针头，采用口内注射法进行上牙槽后神经阻滞麻醉，成功率为98％。
Higher injection temperature makes flame lift-off length decrease uniformly and asymmetry increase slightly.
初始喷油温度的升高会造成火焰浮起长度的减小，但不对称性的变化并不明显。
Several important factors are discussed, such as buffer systems, terminating ions, column effective length and injection time of sample and terminating solution.
详细讨论了影响富集的缓冲体系、尾随离子种类、毛细管有效长度、进样时间和等速电泳时间等重要因素。
Lateral sweep efficiency is the function of injection-and-production system, angles between direction of injection and fractures, and the relative length of fractures.
平面波及系数是注水方式、裂缝走向夹角及裂缝相对长度的函数。
Lateral sweep efficiency is the function of injection-and-production system, angles between direction of injection and fractures, and the relative length of fractures.
平面波及系数是注水方式、裂缝走向夹角及裂缝相对长度的函数。
应用推荐