The effect of the combustor temperature, pressure and coefficient of residual oxygen was experimentally investigated when the fuel was injected into the combustor.
对燃料喷入时的燃烧室温度、压力及推进剂余氧系数等工作参数进行了试验研究。
The resultant cold, gaseous nitrogen is now injected into the engine's cylinder (see diagram) along with a mixture of water and glycol, known as a heat-transfer liquid, that is at room temperature.
由此产生的冷冰的气态氮被注入发动机汽缸（见图）。与此同时，乙二醇与水的混合物也注入其中，这种混合物是一种常温环境下的“传热液体”。
The static and dynamic mechanical properties have been studied for PP that have been injected at different melt temperature and mold temperature.
本文研究了在不同的熔体温度和模具温度下，注射成型的聚丙烯塑料试样的静态和动态力学性能；
Puffing gas can reduce the plasma temperature in the scrape off layer (SOL). Injected impurity can increase the radiation power in SOL. Both of them make the heat load on the plate target smaller.
喷气能降低删削层（SOL）处等离子体温度，注入的杂质增加了SOL处的辐射功率，使靶板的负载降低。
Aqua ammonia with different flow rate was injected into the furnace at different temperature locations by different mechanical atomizers.
使用不同的机械雾化喷嘴，在不同温度点喷入不同流量的氨水。
Under the same temperature, Strength of coke increases after the reaction and coke fines decreases as the amount of UPC being injected into coke layer increases.
同一温度条件下，随着焦炭层喷吹UPC量的增加，气化反应后焦炭的强度提高，粉末量减少。
The influences of the composition of mobile phase, the flow rate, the temperature and the injected quantity on the enantiomer rententivity and selectivity were examined and discussed.
考察了流动相组成、流速、进样量和温度等因素对对映体分离的影响。
The high temperature of stratum and incompatible of injected water and formation water are the key points of scaling and pressurizing.
储层温度高和注入水与地层水配伍性差是注入水结垢造成压力升高的主要因素。
The control of mold temperature in injecting process has extraordinary important influences not only on the quality of the injected products but also on the process itself.
注塑模具的温度控制对注塑工艺和注塑件的质量有非常重要的影响。
The experimental results show that discharge temperature and specific power of compressor are influenced by oil-injected flow and oil cooling capacity.
实验结果表明，压缩机排气温度和比功率受到喷油量和油冷却量的影响。
The physic liquor temperature injected in the blood vessel of the patient is about equal to the blood temperature.
使输入患者血管中的药液温度和血液温度基本相同；
The impact of injected steam temperature on compressor pressure ratio is relative…
低工况时，水蒸气的注入使涡轮的折合流量、膨胀比皆增大；
This temperature is high enough to spontaneouslyy ignite the fuel oil as it is injected into the cylinder.
当油气混合燃料被压缩时，不仅气缸里的压力上升，可燃混合气的温度也随之增加了。
This temperature is high enough to spontaneouslyy ignite the fuel oil as it is injected into the cylinder.
当油气混合燃料被压缩时，不仅气缸里的压力上升，可燃混合气的温度也随之增加了。
应用推荐