He did succeed in casting an enduring literary spell.
他的作品确有经久不衰的魅力。
Process bars can effectively reduce residue stress in casting.
合理的工艺筋可有效降低铸件的残余应力。
Had she been wrong in casting the deciding vote which approved the alliance?
她投了那关键的一票，批准建立这种联盟关系，是不是错了？
The results showed that AM60B magnesium alloys has an evident heredity in casting.
结果表明，AM 60 B镁合金在铸造过程中具有明显的遗传性。
Experienced in casting, machining, assembly, especially in gearbox and valve industry.
具有铸造、机加工、组装工作经验，特别是齿轮箱或阀门工业。
Preforms with waveguide structure have been formed by using a built -in casting method.
用内铸法制得了具有波导结构的预制棒。
The near-liquidus semi-continuous casting (LSC) process was used in casting ZL201 alloy.
采用近液相线半连续铸造的方法制备了ZL201铝合金半固态锭坯。
The reason for resistance in casting in slab caster is analyzed, some correct measures found out.
分析了板坯连铸机拉坯阻力产生的原因，找出了正确处理措施。
The existing bimetal composite processes mainly are of cast-in casting, cast cladding and welding.
目前的双金属复合工艺主要是镶铸、包覆铸造以及焊接。
It is very important of resin-sand technology applied in casting for increasing the quality of the cast.
铸件生产中树脂砂工艺对于提高产品质量有着重要意义。
The casting roller in casting-rolling mill is the important tool to manufacture the cast plates and strips.
铸轧辊是铸轧机列生产铸轧板坯的重要工具，铸轧辊各项参数的控制对板形精度控制至关重要。
The compaction rate of the moulding sand is an essential index showing the sand moisture in casting practice.
型砂紧实率是反映铸型用砂含水量的一个重要指标。
How to apply APQP in casting production, and make the casting meet the requirement of customers was discussed.
结合生产实践，论述了如何在铸造生产中运用APQP来组织生产，使产品质量达到顾客满意的要求。
Melt Purityporositymechanical properties relationships in casting aluminum alloys have been reviewed in this paper.
综述了铸造铝合金熔体洁净度-疏松-力学性能三者之间的关系。
The difference of the two kinds of filler and theirs application in casting material of epoxy resin were discussed.
探讨了两种填料的不同之处，以及它们在环氧浇注料中的应用。
In casting, forging, stamping, plastic, rubber, glass, ceramics, powder metallurgy industry production is widely used.
在铸造、锻造、冲压、塑料、橡胶、玻璃、粉末冶金、陶瓷等生产行业中得到广泛应用。
Optimization model regarding raw materials mixing in casting production was built on the basis of minimal mixture cost.
以铸造配料成本最低为目标函数，建立了铸造优化配料数学模型。
The paper analyzes characteristics of tundish refractory, and raises suitable baking rules of CCM tundish in casting process.
文章对中包用耐火材料的特点进行了分析，提出适合连铸工艺生产的中包烘烤制度。
It is well known that breakout is the most serious accident in casting, it will cause a huge direct or indirect economic loss.
众所周知漏钢是连铸生产中最为严重的生产事故，造成巨大的直接和间接经济损失。
On the analysis of cause of crack in casting reinforcing steel bar and concrete board, countermeasures are put forward for reference.
通过对现浇钢筋混凝土板出现裂缝的原因分析，提出相应的预防和处理措施，供施工单位参考。
This paper presents a new method in which the coating layer is absorbed by low vacuum for determining the permeability of coating used in casting.
提出了用负压吸附涂料层的方式测试涂料透气性的新方法，并推导出了在该方法下计算涂料透气性的数学表达式。
To prevent defects of continuous cast slabs, it must be considered to control the stresses and strains in slabs in casting machine design and operation.
为防止板坯连铸中的缺陷，铸机的设计及生产必须考虑到控制铸坯上的应力和应变。
Research on that metallic melts transforms from liquid to solid state based on heat transfer theory is an important discipline in casting solidification.
研究基于热传输理论的熔融金属从液体转变到固体状态变化过程是铸件凝固研究的重要分支。
It points that the lead tolerance in molten iron should be under 0.0008% if the reject rate is controlled under 0.5% in casting the complicated engine cylinders.
指出在生产这类复杂零件时，要将缸体渗漏废品率控制在0.5%以下时，铁液中铅的含量要控制在0.0008%以下。
In this article, it is emphasized, through explanations and analysis that the correct position of head and the free arm plays an important part in casting techniques.
通过本篇的叙述与分析，进一步强调头与非投掷臂的正确动作，在投掷技术中的重要意义。
The requests for dry-sand, vibrating table, structure of negative pressure sanrl box and proceedings to be noticed in casting pro-cesss have been put forward definitely.
结合工厂多年的生产经验，对于砂性能、振实台和负压砂箱的结构以及负压浇注过程中的注意事项提出了明确的要求。
The recombination activity of grain boundaries (GBs) in casting multicrystalline silicon (mc-Si) was investigated through an electron beam induced current (EBIC) technique.
本文利用电子束诱生电流（EBIC）对铸造多晶硅中晶界的复合特性进行了研究。
The recombination activity of grain boundaries (GBs) in casting multicrystalline silicon (mc-Si) was investigated through an electron beam induced current (EBIC) technique.
本文利用电子束诱生电流（EBIC）对铸造多晶硅中晶界的复合特性进行了研究。
应用推荐