Its advantages are shorter regulation time and lower non-ignition rate.
此线路具有调整时间快和失燃率小等优点。
The effect of hydrogen on methane combustion and ignition temperature, burning rate and burnout time are discussed through analyzing the calculated results.
通过分析计算，讨论了氢气对甲烷燃烧过程及着火温度、燃烧速率、燃尽时间的影响。
Combustion parameters such as ignition temperature, peak temperature of maximum weight loss rate, burnout temperature, maximum rate of combustion, and combustibility index were analyzed.
分析了燃烧特征参数如着火温度、燃烧速率最大时的温度、燃尽温度和最大燃烧速率以及燃烧特性指数。
With the carbon content of dry ash-free basis increasing, ignition activation energy increases and reaction rate falls.
干燥无灰基固定碳含量增加，着火活化能增加，反应速率减小。
Test results show that wood has longer ignition time, less CO yields and less specific extinction area, but its heat release rate is between CR and PVC belts.
结果表明，木材与CR ，PVC输送带相比点燃时间较长，热释放速率介于两者之间，CO生成率和比消光面积较小；
By a lot of experiment, the author claimed a soft arc striking technic which lead the arc ignition success rate to as high as above 90%.
作者还通过大量的试验，以软起动引弧方式，使焊机的引弧成功率达90%以上。
The igniter is the core of the ignition technology. The control of the ignition parameters directly influence the success rate of the ignition.
点火器是点火工艺的核心，点火参数的控制直接影响到点火的成功与否。
For external radiation ignition manner, a series of small-scale fire tests were conducted in a cone calorimeter in accordance with ISO 5660. Heat release rate and mass loss rate were measured.
外部辐射着火的方式采用符合ISO 5660标准的小型锥形量热计来实现，测量其热释放速率及质量损失速率。
The control of auto-ignition time and heat release rate is the most difficult technical question in realizing HCCI combustion.
但HCCI燃烧存在运转范围窄、着火时间和放热率不好控制等缺点，具体实施上还有许多困难。
As an ignition circuit, the problem how to ensure the higher success rate of ignition and reduce the disturbance to control system is all the welding personnel need to face.
如何既能保证引弧成功率高，又能实现以降低频率的方式减小对电网和控制系统的干扰，是设计引弧电路所要解决的问题。
The effects of ignition delay on the maximum explosion pressure and maximum rate of pressure rise are very noticeable;
点火延迟时间对其最大爆炸压力和最大压力上升速率的影响十分明显；
The H2O2 flow has decisive effect on ignition process, and the motor cann't be ignited when the oxidizer flow rate is less than the minimum ignition flow rate.
H2O2的流量对点火过程起决定性作用，当氧化剂流量低于最小点火流量时，发动机将无法点火。
The test results show that, with the increase of the octane number, the ignition timing delayed, the combustion rate decreased, and the cylinder pressure decreased.
研究结果表明，燃料辛烷值增加，着火始点推迟，燃烧反应速率降低，缸内爆发压力降低。
They are employed in furniture, carpeting, bedding, textiles, electronics and plastics to reduce the risk of ignition and slow down the rate at which things burn.
阻燃剂在家具，地毯，卧具，纺织品，电子器件以及塑料制品领域广泛应用于降低物品起火风险，减慢物品燃烧速率。
There will be a conspicuous rise in semi-char ignition temperature when the heating rate is increased.
随着加热速率的增加，半焦的着火温度明显上升。
Since the ignition delay of DME is shorter than that of diesel, thus makes the lower value of maximum cylinder pressure, maximum rate of pressure rise and combustion noise.
二甲醚喷油延迟角比柴油大，最高爆发压力、最大压力升高率、燃烧噪声比柴油低；
With the rise of heating rate, the maximum release rate of volatile and combustion rate of char, the burnout temperature and the combustible parameter increased, but the ignition temperature…
各试样的挥发分最大释放速率、固定炭最大燃烧速率、燃尽温度均呈增加趋势，它们的燃烧特性均随升温速率的升高而变好。
The ignition system plays an important role in the integer characteristic structure of high rate of revolving battery gun.
发火机系统在转管武器的整个性能结构中占有重要的作用。
The ignition delay was shortened by increase intake pressure due to higher intake temperature, which resulted in higher smoke, and this phenomenon was more obvious at high EGR rate situation.
提高进气压力由于进气温度的影响使滞燃期缩短，大EGR率尤其明显，导致碳烟峰值随进气压力升高而增大。
The ignition delay was shortened by increase intake pressure due to higher intake temperature, which resulted in higher smoke, and this phenomenon was more obvious at high EGR rate situation.
提高进气压力由于进气温度的影响使滞燃期缩短，大EGR率尤其明显，导致碳烟峰值随进气压力升高而增大。
应用推荐