Exclusivity: if set to true this queue can only be used by the declaring consumer.
排他性：如果启用，队列只能被声明它的消费者使用。
Height - cell height; if set to 0, the cell's height will expand so its contents fit.
Height—单元格高度；如果设置为0，则单元格高度将扩展，以便能放得下内容。
The special register, if set, takes precedence over the database configuration parameter.
如果设置了特殊注册表的值，特殊注册表将优于数据库配置参数。
A flag, if set, indicates to automatically delete all stored data at application startup.
一个flag，如果设置了，那么表示在应用程序启动时自动删除所有已存储的数据。
The normalization checking attribute, if set to on, will normalize the input text if necessary.
如果打开了规范化检查属性，那么会在必要时对输入文本进行规范化。
Auto deletion: if set to true the queue will get deleted after all consumers have ceased using it.
自动删除：如果启用，那么队列将会在所有的消费者停止使用之后自动删除掉自身。
Experiment shows that it can get a high precision rate if set a high threshold and high similarity.
实验结果表明，当取高阈值且高相似度时，就可得到很高的准确率。
Auto deletion: if set to true the exchange will get deleted after all queues bound to it have been deleted.
自动删除：如果启用，那么交换器将会在其绑定的队列都被删除掉之后自动删除掉自身。
The compiler processes command options as they are encountered, just as if set out on the command line.
当编译器遇到命令选项时就处理它们，就如同在命令行上发出命令一样。
A backstop profile will be used if no more specific profile applies, and if set to UACC NONE, it denies access.
backstop配置文件将在没有适用的特定配置文件时使用，如果设置为uacc NONE，则拒绝访问。
If the file is executable, the suid or sgid bits, if set, will be displayed as lowercase s, otherwise they are displayed as uppercase s.
如果文件是可执行的，suid或sgid位如果已设置，将会显示为小写的s，否则就显示为大写的s。
CaseStartingFolder (OVP, controls location of new cases) - if set, this property controls where the new case (an instance of the CaseFolder sub-class) is filed upon creation.
CaseStartingFolder (ovp，控制新案例的位置)—如果设置了这个属性，它控制在创建时新案例(casefolder子类的实例)归档的位置。
If set to 14 Hz, bass below this point will be filtered.
如果设置为14赫兹，低于这个点低音将被过滤。
If set to publish, the post will be saved and published to your site.
如果被设置为发表，文章会被保存，并同时发表到你的站点上。
If set to 0, this function will be disabled and any data received will be ignored.
如果设置为0，这个功能将被禁用，任何收到的数据将被忽略。
If set to 1, the modem will accept data and buffer it until the unit is synchronized.
如果设置为1，调制解调器将接收数据并存入缓冲区，直到单元同步。
If set to ANY, the optimizer is sensitive to the actual number of cpus that are online.
如果设置为any，优化器就对联机的实际CPU数目敏感。
CCACHE_DISABLE — If set, tells ccache to invoke the compiler proper, bypassing the cache.
CCACHE_DISABLE——设置这个选项告诉ccache完全调用编译器，从而绕过缓存。
If set to partial, as shown below, the default behavior will be to use the Design Filters.
如果设置为partial，如下所示，默认行为就是使用DesignFilters。
If set to a valid typeface name, the function enumerates all fonts with the specified name.
如果设置为一个有效的字体名称，函数枚举所有带指定名称的字体。
If set, three digit exponents are allowed. If not set, only two digit exponents are allowed.
如果设置，那么三位指数是允许的。如果没有设置，那么仅允许两位指数。
If set to "false", search for components to include in response will be performed on all tree.
如果该属性被设为“false”，那么将会在整个树中搜索要加入到响应中的组件。
If set, when sending a broadcast only registered receivers will be called — no BroadcastReceiver components will be launched.
如果发送广播时设置了这个标志，那只会调用注册了的接收器——BroadcastReceiver组件不会被启动。
If set to a port name, then a corresponding entry must exist in the services file (operating system-specific port listing file).
如果将该参数设为端口名称，那么在services文件(特定于操作系统的端口列表文件)中必须有一个相应的条目。
CCACHE_RECACHE — If set, tells ccache to ignore the existing entries in the cache and calls the compiler; but for new entries, it caches the result.
CCACHE_RECACHE——设置这个选项告诉ccache忽略缓存中现有的条目并调用编译器；但对于新的条目，则缓存结果。
If set to too low, this field reduces the throughput by throttling the CPU usage, in turn affecting performance (that is, increasing wait time of an application's request to be served).
如果将此字段值设置得过低，它会限制CPU的使用，从而降低吞吐量，进而影响性能(即增加处理应用程序请求的等待时间)。
If set to too low, this field reduces the throughput by throttling the CPU usage, in turn affecting performance (that is, increasing wait time of an application's request to be served).
如果将此字段值设置得过低，它会限制CPU的使用，从而降低吞吐量，进而影响性能(即增加处理应用程序请求的等待时间)。
应用推荐