Host Port Interface of DSP implements interprocessor communication.
处理器之间的通信由dsp的主机接口实现。
The Linux Host Type has been chosen, and the Host port name should be entered in the final box.
LinuxHostType已被选中，随后，主机端口名称也会被输入到最后的那个框内。
This is caused by the lack of HTTP traffic being routed through the network proxy recorder on local host port 1080.
这是由于缺少HTTP地址流量造成的，这个地址流量是通过网络代理记录器在本地主机端口1080按照线路发送的。
The controller is used to translate requests coming from host port because DDR2 SDRAM could not execute these com- mands directly.
DDR2内存不能直接识别主端口的请求命令，必须经由内存控制器处理后才能执行。
The memory spaces configuration, synchronous serial interface (SSI), serial communications interface (SCI), host port of the DSP system are summarized.
概述了DSP系统的存储器空间设置、同步串行接口、串行通讯接口、主接口的特点；
This paper introduced the communication principle of USB2.0' protocol layer and the division, design and realization of the core part of USB2.0' host port controller.
本文简要介绍了USB2.0协议层的通信原理，描述了USB2.0主机端控制器核心部分的划分、设计及实现。
Each node is configured using a contribution, a composite, and the properties of the environment, like host and port, where the node is run.
每个节点使用某个贡献包、某个组合和运行节点的环境的属性(例如主机和端口)进行配置。
You will need to supply host and port information for your mail server, sender and recipient email addresses, and, in most cases, server authentication information.
您需要提供您的邮件服务器的主机和端口信息、发送器和接收器邮件地址，多数情况下都需要的服务器验证信息。
Specify host and port, the default LDAPS port is 636 but it could be anything, depends on what port the LDAP server USES.
指定主机和端口，默认的ldap端口是636，但可以是任何端口，这取决于LDAP服务器使用的端口。
Check the host name associated with port 9443.
选择与端口9443关联的主机名。
The SOP is a security restriction that basically forbids a page loaded from a certain origin (meaning the protocol/host/port trio of the URL) to access data from a different origin.
SOP是一种安全性约束，它实际上禁止从某个源（即URL的协议/主机/端口三元组）装载的页面访问来自不同源的数据。
Viewing port assignments using Host aliases.
使用HostAliases查看端口分配。
In the SocksCap Settings dialog box, enter your SOCKS server host name and port.
在SocksCap Settings对话框中，输入您的SOCKS服务器主机名和端口。
If you don't specify host and port, the defaults are localhost and 1099, respectively.
如果没有指定主机和端口，那么默认值分别是localhost和1099。
Be sure to replace localhost and 9080 with your WebSphere Application Server's respective host and port values.
确保使用您的WebSphereApplicationServer的主机和端口值分别替换localhost和9080。
Use an LDAP browser of your choice and connect to the LDAP using the host, port, BaseDN and BC collected.
使用您选择的LDAP浏览器，使用收集的主机、端口、BaseDN和BC连接LDAP。
Alternatively, you can specify a host and port using the — host and — port options.
另外，也可以使用——host和——port选项指定主机和端口。
rmi:///jndi/rmi:[//host[:port]]/JMXConnector
deployer:geronimo:jmx:rmi:///jndi/rmi:[//host[:port]]/JMXConnector
To resolve the failure, either use a port that is in the virtual host group or add port 12080 to the virtual host group.
要解决这个问题，要么使用虚拟主机组中的一个端口，要么将端口12080添加到虚拟主机组中。
As described earlier, a single pass of either the host or port scanning information is only useful for the instant in time when the scan was executed.
如前所述，如果只进行一次扫描，那么主机或者端口扫描信息仅在执行该次扫描的时候是有用的。
In this step, you need to specify the host and port for the node.
在此步骤中，您需要为节点指定主机和端口。
Only when the application starts can the resource adapter verify whether properties such as host names and port Numbers are correct.
只有当应用程序启动时，资源适配器才能验证类似于主机名称和端口号这样的属性是否正确。
IRC client software then attaches to the server by specifying a host name, port number, and requested nickname.
通过指定主机名称、端口号和所需的别名，将IRC客户机软件连接到服务器。
For servers, the system needs to know all of the application servers, their current status (started or stopped), and their communication ports (host and port number).
对于服务器，系统需要知道所有应用服务器、它们当前的状态(开始或停止)及其通信端口(主机和端口号)。
After the deployment completes, note the Host, Port, User, and Password information as shown in Figure 20.
完成部署后，请注意主机、端口、用户和密码信息，如图20所示。
The connection is established to the remote host on TCP port 22.
建立到远程主机的TCP端口22的连接。
Note in Figure 4 that the host and port fields specify the address where your ApacheDS is listening.
请注意在图4中，主机和端口字段指定了ApacheDS侦听的地址。
If you do so, it will be called from the browser if you simply specify the host: port address in the browser's address line.
如果这样做，而且您仅在浏览器地址行中指定host：port地址，则它将从浏览器中调用。
They will need the MIB, and you will need the host name, port, and community string for the SNMP Manager.
他们需要这个MIB，而您需要SNMPManager的主机名、端口和社区字符串。
To create an instance of AdminClient, you need to pass the appropriate host name, port number, and connector type.
您需要通过合适的主机名、端口号和连接器类型才能创建AdminClient实例。
应用推荐