When bottom hole liquid increases in gas well, back pressure increases, and gas production is reduced.
在气井中，当井底积液增多时，会增大井底回压，降低产气量。
This paper points out that the kinetic energy factor-hydrops height method can be applied to diagnose the accurate situation of the bottom hole liquid loading.
文中提出应用动能因子-积液高度法来诊断气井井底积液情况。
And at low flow-rates liquid will weep through the hole, reducing the plate efficiency.
并且在低流速液体意志通过孔啜泣，减少塔板效率。
Also, the paper analyses the error caused by capillary action of liquid, error precision, zenith Angle of hole and container diameter.
并对液体的毛细作用、误差精度、钻孔顶角、容器直径引起的误差进行分析。
Choosing a liquid with higher viscosity indicator and opening suitable damping hole will achieve the requested shock-absorbing effect.
在实际过程中可以通过选用较高粘度指数的减震液和开设合适的阻尼孔，达到要求的减震效果。
A long-pulse laser, whose energy density can cause the liquid mass transferred, can get a greater ablation ratio and a hole with larger cross section.
能量密度达到造成液态质量迁移条件的长脉冲激光，可获得较大的烧蚀率和截面积较大的通孔。
Results Waste rate resulting from burnt head was reduced because of usage of three-hole pinhead in the work of filling liquid medicine.
结果使用三孔针头灌注药液，使最终产品中因“焦头”而被剔除的废品率大大降低。
It can decrease the production of air hole by controlling the stableness of the velocity when female die contacted the liquid of aluminium.
摇盘凸模接触到铝合金液时，控制加压速度平稳一些，可减少气孔的产生。
This paper discusses the factors affecting hole inclination measurement with horizontal liquid surface bore hole TV system.
提出水平液面式孔内电视系统测量孔斜的误差因素。
Using a liquid or gel electrolyte as a hole transfer medium, the DSSCs with 4.31 % or 2.75 % global photon-to-electron conversion efficiency was obtained, respectively.
以液态电解质和凝胶电解质为空穴传输体，分别制备出了光电转换效率超过4.31%和2.75%的染料敏化太阳能电池。
Dry and solidify the wet film, liquid light sensitive resistance welding, dry the net board and hole wall, etc.
湿膜、液态感光阻焊的干燥和固化；也可用于网版的干燥；板材和孔壁的干燥等等。
The mobility test part comprises a sprue gate, a melting liquid cavity and an exhaust hole.
流动性试验部件包括浇注口、熔液腔和排气孔。
The sprouting hole with suitable aperture can be selected for the system according to the liquid of different natures, so as to realize the reliable printing.
如上系统可以根据要打印的不同性质的液体，选择合适孔径的喷孔，实现可靠的打印。
Quick-open hand hole is set at lower part of the concentrator to clear residual liquid and slag inside the concentrator.
在浓缩罐下部设置了快开式手孔，以使清理罐内残液，残渣；
Methods We changed straight pinhead to three-hole pinhead of filling & sealing machine in the work of filling liquid medicine.
方法将灌封机上的直筒药液灌注针头，改为“三孔”针头。
These structural parameters produce to the different impact of the oil-water separation, the relatively large effect is the diameter of liquid distributor and the hole shape in the all parameters.
经过分析可知，这些结构参数不同程度的影响了油水分离效果，其中对油水分离效果影响比较明显的是配液管的管径和对配液孔形状的选取。
The upper part of the cavity container is provided with a liquid adding hole and a hole plug.
所述空腔容器部分的上侧设有加液孔及孔塞。
The cup, which has a small hole in the bottom, is completely immersed in the liquid to be measured.
这种涂料杯，在底部有一个小孔，在测试过程中被液体浸入。
With the selection of a gas liquid computational model to calculate bottom hole pressure and compare with observed pressure, its relative error is less than 2%.
选用气液两相计算模型计算井底压力并和实测井底压力进行了对比分析，相对误差均小于2 %；
The monitor can automatically measure the annular liquid level changes at well head, and then calculate the bottom hole pressure.
该仪器能够从井口自动监测抽油井内环空液面深度变化，通过分析计算获得井下压力的恢复情况。
The performance of hole-plate and overflow-weir liquid distributors have been measured and a proposal for the design of the two kinds of the distributors is given.
通过对孔板式和溢流堰式液体分布器性能的测定，提出了对该两种分布器设计的建议。
When liquid metal flows through the filter, there will be vacuum produced in filter's hole. Inclusion and gas in liquid metal were absorbed to the filter by vacuum, that cause liquid metal cleaning.
金属液流经过滤介质时，由于流动在孔道内产生真空，液态金属内的夹杂和气体被负压吸附到过滤介质的表面而产生净化作用。
One brake wall is it enter this to extend through hole this, it USES for to be horizontal to move in this liquid.
一个制动器臂通过该孔延伸进入该腔，用于在该液体腔中横向移动。
The utility model belongs to a hole drilling device, specifically, a sub-immersed liquid hole drilling device.
本实用新型属于一种钻孔装置，具体涉及一种地浸注液钻孔孔口装置。
The deformation mechanism of hydropiercing was concluded based on the calculation results. Influence of liquid internal pressure on hole quality was investigated.
在此基础上，阐述了液压冲孔的变形机理，分析了液体压力对冲孔质量产生的影响。
To low production and low pressure wells, low pressure makes liquid depth in bore hole to be low before it closed.
低产低压油井关井后，井筒内出现段塞流，测试资料表现出很长的早期段。
The utility model is applied in sub-immersed liquid hole drilling.
本实用新型用于地浸注液钻孔。
The plating liquid having reached the upper end circulates through the through-hole of the tubular electrode.
已经到达上端的电镀液穿过管状电极的通孔循环。
The results provides reference for further research of the gas liquid of down-hole.
该结果为井下螺旋式气液分离的进一步研究提供了参考依据。
The results provides reference for further research of the gas liquid of down-hole.
该结果为井下螺旋式气液分离的进一步研究提供了参考依据。
应用推荐