The stress relaxation was mainly related to the heating temperature and time.
加热温度及时间是决定应力松弛的关键因素。
The brazing of PCD tools requires exact heating temperature and soaking time.
聚晶金刚石复合片刀具的焊接，严格要求加热温度和时间的参数。
The ferric vacancy concentration varies with composition and heating temperature.
尖晶石相和其中的铁空位浓度随组成和烧结温度而变化。
DCR of these erythrocytes gradually decrease with increase of heating temperature and time.
红细胞受热后dcr随受热温度及时间增加而降低。
It was found that tinidazole remained stable under the high er conditions of heating temperature.
可以发现替硝唑的稳定性在高温条件下不受影响。
The effect of different heating temperature on garlic freeze drying time was studied by single factor test.
通过单因素试验，探讨了不同加热温度对大蒜冻干时间的影响。
The effect of heating temperature on abrasion resistance of high alloy wear-resistant cast iron was studied.
研究了加热温度对高合金耐磨铸铁耐磨性的影响。
The results showed that the composition and construction of thistle board vary with the heating temperature.
结果表明：纸面石膏板在受热时，其组成、结构将发生改变。
Aim To study the effect of heating temperature and heating duration on HMF formation in different floral honeys.
目的研究加热过程对不同种类蜂蜜中羟甲基糠醛(HMF)含量的影响。
The fluorescence induced by laser in heated oil has increased intensity with heating time and heating temperature.
本文报道了几种精炼油加热后的激光诱导荧光强度的变化与加热时间及温度的关系。
The results prove that the initial bonding strength mostly depends on total reduction and heating temperature of al.
结果表明，轧制变形程度和铝层加热温度都是影响复合板初结合强度的主要因素。
All these indicate that heating temperature plays an important role in the crystal structure formation of PET fiber.
充分说明了温度在加工过程中对PET纤维结晶结构的形成所起的作用。
The heating temperature and holding time had distinct effects on the copper diffusion depth in the stainless steel socket.
结果表明：铜在不锈钢衬筒中的扩散深度随着停留时间和加热温度的增加而增加；
The composition of cholesterol oxidation products differed on different heating temperature, time and amount of cholesterol.
胆固醇氧化产物组成和生成量与胆固醇的量、加热温度及加热时间有关。
The requirement to flow, pressure, heating temperature and purity of converter gas used in reheating furnace were introduced.
介绍了加热炉在使用转炉煤气作为燃料时，对其流量、压力、加热温度和纯洁度的要求。
The results show that heating temperature and holding time are two important factors affecting the grain size and uniformity.
实验表明，加热温度和保温时间是影响晶粒尺寸和均匀性两个重要的因素。
The key factors in each decoration procedure are specified, including heating temperature and time space, paste selection, etc.
详细说明了各装饰工艺中的关键因素，例如加热温度和时间、印料的选择等。
Study on the effects of different heating temperature, heating time on the protein denaturation condition of the chicken marrow.
研究了不同的加热温度﹑加热时间对鸡骨髓中蛋白质变性程度的影响。
Effects of heating temperature and duration, shaping pressure etc. on the properties of this glass composite have been discussed.
探讨了烧成温度、保温时间、成型压力等工艺因素对于该复合材料性能的影响。
Intermittent freeze drying equipment for control of drying at different stages of heating temperature and vacuum degree requirements.
间歇式冻干设备便于控制物料干燥时不同阶段的加热温度和真空度的要求。
The activity of PPO in the juice decreased gradually with the rise of heating temperature and the extension of pressure holding time.
随着保压时间的延长和温度的升高，桃汁中多酚氧化酶相对活性逐渐降低。
The influences of cooling rate after the forge on the heating temperature and time of apheroidized annealing of steel T10 was studied.
研究了锻造后的冷却速度对T10钢等用球化退火加热温度和保温时间的影响。
The affects of sort of surfactant, mass ratio of compound surfactants, heating temperature and time on the oil recovery were investigated.
考察了表面活性剂种类、复合表面活性剂的配比、加热温度和时间等条件对油分回收率的影响。
The influence of melting rate, super heating temperature, pouring temperature and modification on high chromium cast iron were researched.
对高铬铸铁的熔炼速度、过热温度、浇注温度和变质处理进行了研究。
The effect of heating temperature, holding time and cooling mode on its crystallizability and dissolution rate of potassium is not obvious.
改变合成温度、保温时间以及冷却方式等，对合成试样的结晶性能以及试样中钾元素溶出率的影响很小。
The parameters such as POS concentration, POS heating temperature, fuel load and oxygen content have high influence on combustion efficiency.
石油焦渣油浆的浓度、油焦浆的加热温度、负荷和氧量对其燃烧效率有很大影响。
The results show that the heating temperature and the ways of cooling and loading are of great influences on the bond performance of reinforced concrete.
结果表明，受热温度、冷却方式和加载制度对高温后钢筋混凝土的黏结性能有很大影响。
We have optimized simultaneously TISAB consuming, heating temperature and time, and made an optimized choice with comparison between pretreatment methods.
同时对TISAB用量、加热温度、时间及分析方法作了优化选择和比较，结果满意。
By changing heating temperature and holding time, the austenite grain growth behavior of a low carbon steel under different heating conditions was studied.
通过改变均热温度和保温时间，研究低碳钢的奥氏体平均晶粒尺寸与时间的关系，及奥氏体晶粒各尺寸范围的分布规律。
Send thickness of the glass can be processed in accordance with the relevant requirements of glass conditioning, heating temperature may need to set in advance.
玻璃传送厚度可根据有关加工玻璃工艺要求调节，加热温度可按需要事先设定。
应用推荐