Analyses the internal gear tooth profile by using conjugate outline's meshing theory.
利用共轭齿廓的啮合理论对内齿轮进行了齿形分析。
The evaporation is affected by temperature and wearing condition of gear tooth flank.
汽化程度与齿面温度及磨损状态有关。
Before shaving teeth gear tooth shape of processing with hob called before shaving hob.
剃齿前加工齿轮齿形用的滚刀称为剃前滚刀。
Gear tooth thickness at the site are unilateral wear, so gear can be rotated 180 degrees to use.
齿轮在齿厚部位都是单侧磨损，所以可将齿轮翻转180度使用。
However, the research on the bending strength of large module gear tooth root is scarce until now.
但是，目前对大模数齿轮弯曲强度的研究还比较少，因此研究大模数齿轮轮齿弯曲强度具有重要意义。
Pressure ball machine parts have hollow shaft, wheel, small gear tooth circle, roller skin, motor, etc.
压球机零件有中空轴、齿圈轮、小齿轮、辊皮、电机等。
Full radius hob on tooth tip is one of the effective measures by increasing gear tooth bending strength.
应用齿顶整圆弧滚刀是提高齿轮弯曲疲劳强度的有效措施之一。
The active design technique of hypoid gear tooth face provides a kind of fresh method of the hypoid gear design.
准双曲面齿轮齿面主动设计技术为准双曲面齿轮副的设计提供了一种全新的思路。
And it analyzed that hob tooth height and tooth top pour round radius impacted on gear tooth root crooked stress.
分析了滚刀齿高和齿顶倒圆半径对所切齿轮齿根弯曲应力的影响。
The curvilinear shape of chain gear tooth plank is the basic cause of saw-tooth phenomenon in the sintering pallet.
链轮齿板的曲线形状是造成烧结机台车在回车道上起拱的根本原因。
The stub gear tooth is often adopted in the involute planetary gear transmission with a few tooth number difference.
在渐开线少齿差行星传动中通常使用短齿，其齿根高与正常齿相同，而齿顶高小于正常齿。
This paper proposes a new method to modify the cycloid gear tooth of reducer in order to improve the gear engagement.
本文以改善摆线针轮减速器轮齿啮合质量为目的，提出了一种新颖的摆线轮齿形修整方式。
A mathematical model of spiral bevel gear tooth surface was built by analyzing manufacture method and meshing theory.
通过分析锥齿轮的加工方法和齿轮啮合理论，建立了螺旋锥齿轮齿面数学模型。
In the process of the teeth, hob manufacturing error of gear tooth shape of the main impact error and the festival deviation.
在切齿过程中﹐滚刀的制造误差主要影响齿轮的齿形误差和基节偏差。
The SL85 pulse wheel assembly is imprinted with magnetic poles that provide higher pulse counts than traditional gear tooth wheels.
脉冲的SL 85车轮印有大会提供比传统的齿轮齿车轮更高的脉冲计数磁极。
Based on the method of non-contact pick-off detection of gear tooth, the detection system of a radial multi - gear flow was designed.
基于非接触式齿轮速度传感器检测原理，设计了一种径向多齿轮流量变送器测量系统。
The exact computing formulas for the normal chord length and the set angle of the gear tooth micrometer callipers have been derived here.
本文导出了法向弦长和公法线千分尺安置角的精确计算公式。
The speed reducer gear tooth surface through contact fatigue strength to calculate, through the tooth root bending fatigue strength check;
减速器中齿轮通过齿面接触疲劳强度来计算，通过齿根弯曲疲劳强度验算；
Dynamic speckle photography of the gear tooth has been achieved by combining a pulsed ruby laser with the external synchronizing trigger signal.
红宝石脉冲激光器和外同步触发信号结合实现了齿轮轮齿动态散斑图的记录。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
In this paper, a. new algorithm substituting an optimized round arc for the outline of tooth curve of an epicyclic gear tooth with long amplitude is discussed.
本文提出了用最优化圆弧代替长幅外摆线轮齿廓曲线的一种新型算法。
Gear tooth face serious wear new gear should be changed, if only gear at both ends of the plane wear, can be in surface grinding machine on grinding repair light.
齿轮齿面严重磨损时应更换新齿轮，如果只是齿轮的两端平面磨损，可在平面磨床上磨削修光。
Simulation of plastic deformation in gear tooth is implemented in consideration of mesh stiffness, which is fundamentally identical to the results from experiments.
考虑瞬时啮合刚度的影响，对轮齿表面的塑性变形进行了仿真计算，模拟结果与实验结果有较好的一致性。
However, after shaved by shaving cutter with true involute profiles, there are the "mid-concave" phenomena on the pitch points of shaved gear tooth profiles inevitably.
然而用标准渐开线齿形剃齿刀剃齿后，在工件齿形节点附近会出现不同程度的“中凹”现象。
The MLX90217 is a self adjusting digital output rotary position gear tooth sensor designed for use in automotive camshaft sensing as well as other speed sensing applications.
MLX90217是一款自适应调整、数字输出的旋转位置齿轮传感器，可应用于汽车凸轮轴传感器以及其它速度传感器。
The main idea of the single gear tooth analysis is that the vibration signals collected with high sampling rate are divided into a number of segments with the same time interval.
它将振动平均信号等距分段(所分段数与被监测齿轮齿数相等)，然后对分段信号进行频谱分析等。
The common gear tooth profile curve launches after neighborhood higher order step taylor's series, can discover the tooth face meshing point neighborhood gap is 2 step infinitely greats.
一般齿轮齿形曲线在一点邻域的高阶阶戴劳级数展开后，会发现齿面啮合点邻域间隙为2阶无穷小。
Using present bending fatigue limit data of gear tooth and other materials of gears, the calculating method of re liability is proposed for bending strength of gear tooth st steady condition.
利用现有齿根弯曲疲劳极限应力数据及其它齿轮资料，提出了稳定工况下齿轮齿根弯曲强度可靠度计算方法。
Using present bending fatigue limit data of gear tooth and other materials of gears, the calculating method of re liability is proposed for bending strength of gear tooth st steady condition.
利用现有齿根弯曲疲劳极限应力数据及其它齿轮资料，提出了稳定工况下齿轮齿根弯曲强度可靠度计算方法。
应用推荐