By using melt gear pump, production efficiency and product quality can be improved and production cost can be reduced in the polymer processing.
在聚合物加工中使用熔体齿轮泵可以提高生产效率和产品质量，降低生产成本。
Park Lemke gear pump motor is a kind of parts for cranes.
泊姆克齿轮泵马达是用于起重机的一种配件。
The synchronization gear pump can reduce the radial and boost the work pressure.
同步齿轮泵能够降低齿轮泵径向力，提高齿轮泵的工作压力。
High viscosity gear pump does not generate pressure, it is only the output flow.
高粘度齿轮泵并不能产生压力，它只是输出流量。
The product is applied to medium, high-pressure gear pump, ram pump, vane pumps, etc.
产品主要应用于中、高压齿轮油泵、柱塞泵、叶片泵等。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
To show the effectiveness of the approach, case study is finally presented for a gear pump.
最后通过齿轮泵的应用实例说明了该优化算法的有效性。
This paper introduces the criterion and some noted problems of gear design for internal gear pump.
本文介绍了内啮合齿轮泵齿轮设计的准则及应注意的几个问题。
If the high viscosity gear pump high pressure adjustment, will make the pump running under overload.
如果高粘度齿轮泵的工作压力调整过高，则会使齿轮泵在超负荷下运行。
PEP - II of the gear pump shaft, and the body USES hardening craft, can obtain more long working life.
PEP-II泵的齿轮与轴共为一体，采用通体淬硬工艺，可获得更长的工作寿命。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
This article presents a new tentative idea for the discharge of the pocketed oil in the hydraulic gear pump.
针对液压齿轮泵困油问题，提出卸荷方法的新设想。
Balanced compound gear pump is a new king of hydraulic pump which combines ring gear with external gear pump.
复合式平衡齿轮泵是将内外齿轮泵融为一体的新型液压泵。
Use of helical gear in gear pump is an effective measure, which can reduce the mechanical voice and flow pulse.
齿轮油泵采用斜齿轮是降低机械噪声和减小流量脉动的一种有效措施。
The inner leakage, as the major factor, affects the efficiency of the cubage of the balanced compound gear pump.
平衡式复合齿轮泵的内部泄漏是影响其容积效率的主要原因。
When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.
安装联轴器时不得用锤敲打，以免伤害齿轮泵的齿轮等零件。
The applications of polymer melt gear pump in plastics extrusion and microcellular plastics forming are introduced.
介绍了熔体齿轮泵在塑料挤出成型及微孔塑料加工中的应用。
The noise is usually one of the common troubles in gear pump. Once solving this, it is good for the normal running.
噪声是齿轮油泵常见的故障之一，解决这一故障有利于齿轮油泵正常工作。
The article expounds the structure design and technical analysis of gear pump twin outlets for viscose filament yarn.
介绍粘胶长丝双出口齿轮泵结构设计及技术分析。
This article will discuss the design of compensating groove in external gear pump by analyzing the gearing characteristics.
该文主要通过分析齿轮的啮合特点来探讨啮合齿轮泵卸荷槽的设计。
Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.
电动机与齿轮泵须用弹性联轴器连接，同轴度小于0.1毫米，倾斜角不得大于1度。
Internal gear pump is the small gear wheel, the big gear for driven wheel, in work big gear with small gear cocurrent rotation.
内啮合齿轮泵中的小齿轮是主动轮，大齿轮为从动轮，在工作时大齿轮随小齿轮同向旋转。
The service life for gear pump is much less than the desired design up to now, which is mainly caused by higher pressure imbalance.
迄今为止，齿轮泵的寿命还远远达不到设计要求，这主要是齿轮泵存在较大的径向不平衡力所致。
The prominent characteristics of gear pump in application to flow metering and fluid transportation were introduced in this article.
介绍了齿轮泵用于流量计量和流体输送时所具有的突出特点。
It has been proved that to make use of squeeze casting to produce the body of gear pump can get good quality casting of aluminum alloy.
试验证明，采用挤压铸造新工艺可以获得优质的铝合金泵体铸件。
Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.
用手转动联轴器时，应感觉到齿轮泵能够轻松地转动，没有卡紧等异常现象出现，然后才可以配管。
It takes the CB gear pump as an example for detailed calculation, demonstrating an effective evaluation method for the assembly ability.
以CB型齿轮泵为例进行了具体的计算，对产品的可装配性作了评价分析。
The features and application scope of different alternating and direct current motors used as the drive device of gear pump were compared.
对比了使用不同类型的交、直流电机作为齿轮泵驱动装置的特点和应用范围。
For often work under high pressure gear pump, the working pressure shall be lower than the rated pressure of the pump 1 ~ 2 pressure level.
对于经常工作于较高压力下的齿轮泵，其工作压力应比泵的额定压力低1 ~2个压力级。
For often work under high pressure gear pump, the working pressure shall be lower than the rated pressure of the pump 1 ~ 2 pressure level.
对于经常工作于较高压力下的齿轮泵，其工作压力应比泵的额定压力低1 ~2个压力级。
应用推荐