The calculation method for bolt pretightening force of tube side gasket and shell side gasket was proposed.
提出了管侧垫片和壳侧垫片螺栓预紧力的计算方法。
Thankfully, I didn't know the extent of it or I would have blown a gasket.
谢天谢地，我当时并不知道花了这么多钱，否则我早就暴跳如雷了。
Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
一般来说，气缸和气缸盖用螺栓紧固在一起，气缸与气缸盖之间用一薄垫圈确保密封良好。
On deck, all hands! Make fast the bunt gasket!
所有人立刻上甲板，赶快拉紧束帆索！
New installation and gasket technologies make maintenance easier and ensure a perfect fit of the gasket and plate pack.
新的安装和垫片技术，使维护更容易，确保垫片和板片的完美契合。
This collar ACTS as a kind of gasket.
这个翻边起一种密封垫的作用。
This collar acts as a kind of gasket .
这个翻边起一种密封垫的作用。
The clapboard is sealed by "U" sealed gasket.
分水隔筋由U形密封圈密封。
Install replacement gasket and thermostat housing.
安装替换垫圈及调温器外壳。
Class 150: Corrugated graphite-filled steel gasket.
150磅级：石墨填充波纹钢板密封垫。
The gasket among unions adopts food grade material.
快接件的垫圈全部采用可食用级材料；
Kit includes: Diaphragm assembly, Disc assembly and gasket.
组件包括：隔膜总成，阀瓣总成和垫圈。
Repair Kit consists of diaphragm assembly, disc assembly and gasket.
维修组件包括隔膜总成，阀瓣总成和垫圈。
The gasket faces of girth flanges shall be machined after final heat treatment.
在最终热处理后翼缘法兰的垫片的端面应进行加工。
The first requirement for a gasket is compatibility with the product being handled.
对于衬垫的第一个要求是同正在操作的产品的相容性。
A 309 ss inlay is standard in the gasket area of the body on ANSI class 2500 valves.
ANSI等级2500阀门的阀体的垫圈区域嵌入309不锈钢是一种标准配置。
Model 9 and NLF9 repair consists of; diaphragm assembly, discs assembly and a gasket.
型号9和NLF9维修组件包括：隔膜总成，阀瓣总成和一个垫圈。
The urethane liner extends over the flange face to serve as the valve's flange gasket.
这种氨基甲酸乙酯延展覆盖到法兰表面，起到阀门法兰衬垫的作用。
Joint sealant gasket of expanded PTFE made of pure PTFE is a continuous low density cord.
膨胀聚四氟乙烯密封胶带是用聚四氟乙烯制成的低密度密封材料。
Optional packing and gasket materials are available for a full range of service conditions.
可提供备选填料和垫圈材料，以满足各种应用环境。
When installing the pipeline with flange, the gasket must be placed between the two butt flanges.
安装带法兰的管路时，必须在两个对接法兰的密封间放置垫片。
Although people seem to think there is an inherent weakness in the Head gasket in fact that's not true.
虽然人们似乎认为缸盖垫片存在着固有的弱点，但其实并不是这样。
If the gasket is not present or must be replaced, select a replacement compatible for the product involved.
如果垫圈不在或者垫圈必须更换，选择一个同相关的产品相容的替代品。
Meanwhile the performance of graphite spiral wound gasket under different technique parameters was analysed.
同时对不同工艺参数下的石墨缠绕垫片性能进行分析。
To prevent this from happening, avoid excessive tightening force and install a new gasket with every cylinder change.
为了防止这种情况发生，避免用过大的上紧力，并且每次换钢瓶的时候装一个新的垫圈。
In the low temperature, corrosive medium or vacuum conditions, with special performance should be considered the gasket.
在低温，腐蚀性介质或真空条件下，应考虑具有特殊性能的密封垫。
O seal: usually the dismantled o seal should be changed totally, but the gasket, etc without breakage also can be reused.
形密封：一般经过拆卸的O形密封应全部更换，对其它密封垫片等，只要没有破损，也可以复用。
The condenser is a tube, elbow, metal hoses, fasteners, F4 rubber lined steel corrugated ring gasket and support component.
本冷凝器是由一组套管、弯头、金属软管、紧固件、F4橡胶内衬不锈钢波纹环垫片及支架组成。
With the example, one method for designing flat cover with welded gasket commonly met in pressure vessel design was presented.
通过计算实例，给出了压力容器设计中常见的焊接密封垫片连接结构的平盖设计的一种方法。
With the example, one method for designing flat cover with welded gasket commonly met in pressure vessel design was presented.
通过计算实例，给出了压力容器设计中常见的焊接密封垫片连接结构的平盖设计的一种方法。
应用推荐