LVC (Liner Variable contour) is a new type of work roll contour. Gap crown can linearly vary with strip width by use of the contour and strip shape performance can be adjusted through shifting.
工作辊辊型是一种新型辊型，这种辊型实现了辊缝凸度随板宽变化成线性变化，并可以通过窜辊来调节板形性能。
The artifacts such as flow gap, lower signal intensity on the veins had features about the shape and location.
静脉低信号和流动间隙伪影有形态和部位特点。
HGC system is the important component in the control system of coldroll, it can control the rolling gap size of stand, and direct effect the shape of plate.
液压压下控制系统是冷连轧机控制系统中十分重要的组成部分，它主要实现机架辊缝大小的控制，对于轧制板材的板形有着直接的影响。
In order to obtain the 3D data of the discharge gap and workpiece shape from the experimental results, a new measurement is proposed.
在试验结果的获取中，为能够得到很难测量的线电极周围的放电间隙和工件形状数据，提出一种新的三维形状测量方法。
Spark-gap length affects the energy of the spark, and the shape of the insulator affects the temperature of operation.
火花间隙的长度影响火花的能量，而绝缘体的形状则影响工作温度。
Given a lattice symmetry, larger absolute photonic band gap was achieved by selecting an air hole shape of the same symmetry.
给定晶格对称结构，选择具有相同对称形状的空气孔能得到较大的绝对光子带隙。
Air gap is one of the important factors which affect the general performances of linear synchronous oscillating motor, thus to seek for a rational shape of air gap is a key point in motor design.
工作气隙是影响直线同步振动电动机工作性能的主要因素之一，寻求合理结构的工作气隙是电动机设计工作中十分重要的内容。
By the technique of intermediate roll shifting, the HC-mill's gap stiffness and the shape control ability is improved significantly.
HC轧机采用中间辊轴向窜动技术，使轧机的横向刚度显著增加，提高了板形控制能力。
By changing the brush diameter, density, the gap between brush bristles and the axis, and the shape of brush edge, the influence of the structure parameters on the seal performance is obtained.
通过改变刷毛直径、刷毛密度、刷毛与轴的间隙以及刷毛齿形，分析了这些结构参数对密封性能的影响规律。
The Fourier analysis method is applied to decompose the air-gap magnetic density into the basic wave and a series of harmonic and wave shape eigen coefficient of air-gap magnetic field are calculated.
采用付立叶谐波分析的方法把气隙磁密分解为空间基波和一系列谐波，进而计算出气隙磁场波形特征系数。
The main reasons resulting in the high oil temperature is that the oil starvation and the gap geometry shape between the bush and the trunnion is not suitable to the dynamic lubricant conditions.
根据分析结果，找到油温升高的主要原因是由于带油不畅和供油量不足引起，提出刮瓦和改造低压供油装置的措施。
The calculating results showed that the optimized geometry of soldering fillet is a concave shape in which the extruding length of the soldering fillet is a little more than the gap height.
计算结果表明，钎缝圆角的最佳几何形状为钎缝伸出长度略大于钎缝高度的凹型。
The gap crown between two work rolls of plate mills and the strip shape can be adjusted by axial shifting of the work rolls, both of them have a special contour.
板材轧机上一对带特殊辊型的工作辊轴向相对移动时，可改变辊缝凸度，调节板形。
Powder or mother granule in rotated fluid-bed will undertaken the action of air flouting force in ring gap, rotating centrifugal force and grity itself and appear cycle rope strain shape.
粉末或者目力在旋转流床内，受到环隙空气浮力，旋转离心力、自身中力作用，呈环周绳股状，粘和剂或包衣液喷入料层形成真球度及高的粒或连续均匀的衣膜。
The effect obviously is changed with welding time, and the effect of gap on shape of molten pool is analyzed as well as the rule of different parameter on the change of molten width is obtained.
分析了间隙对熔池形状的影响，得出不同工艺参数对熔宽变化的影响规律，并分析了电孤形态差异对接头的影响。
Gas-flow and heat-transfer in the wedge-shape air-gap of horizontal evaporation cooling motor is studied by numerical method and experiment.
本文通过数值和实验手段研究了卧式蒸发冷却电机楔形气隙中的流体流动、传热现象。
The melting state, with external blow shape. whether floe fine, fiber jilt into for interchanges between and fiber, intertwining together, presents many small gap.
在融化状态下，借助外力吹制式甩成絮状细，纤维和纤维之间为立体交叉，互相缠绕在一起，呈现出许多细小的间隙。
The melting state, with external blow shape. whether floe fine, fiber jilt into for interchanges between and fiber, intertwining together, presents many small gap.
在融化状态下，借助外力吹制式甩成絮状细，纤维和纤维之间为立体交叉，互相缠绕在一起，呈现出许多细小的间隙。
应用推荐