Temperature drift of gap sensor mainly results from sensor coil impedance drift.
间隙传感器线圈电阻的温度漂移是导致传感器输出漂移的主要因素。
The semi-duplex work form was adopted between suspending gap sensor and controller.
而悬浮间隙传感器和控制器间则采用半双工方式工作。
In this paper a design and research method is developed and created for the gap sensor.
本文主要介绍了高速磁悬浮列车间隙传感器的设计和研究。
In HSMV, the levitation system plays an important role, and the gap sensor is also critical.
悬浮系统是高速磁悬浮列车的关键，而其中的间隙传感器则是悬浮系统的重要组成部分之一。
The gap sensor plays an important role for electromagnetic suspensive system which is a critical component of HSMV.
悬浮系统是高速磁浮列车系统的关键和核心，而间隙传感器又是悬浮系统的重要组成部分。
Finally, a kind of gap sensor is made according to above ideas, and a calibration system for the gap sensor is simply introduced.
最后，根据以上思路研制了间隙传感器，并简要介绍了传感器标定系统。
The gap sensor works in a complex electromagnetism place and there is much disturbance, so it is likely to result in communication failed.
由于间隙传感器工作区域的电磁环境复杂，干扰源比较多，可能会造成通讯失败。
The dynamic characteristics of the gap sensor necessary for suspensive control system in maglev vehicle, are difficult to measure at high frequency by mechanical methods.
在磁悬浮列车中，悬浮控制系统要求间隙传感器的动态特性，但无法用机械方法测试较高频率时的动态特性。
To guarantee good quality of butt laser welding with filler wire, a gap width detecting sensor and a wire feeding system has been designed.
本文针对高质量板材对接填丝激光焊的需要，设计了对缝间隙宽度检测的传感器与送丝控制系统。
In the thesis, a non-contact measurement technology by combining an eddy current displacement sensor with a sonic thickness sensor was put forward to measure timely real plate gap of refiner.
本文对采用电涡流传感器和超声波测厚仪组合实时非接触测量磨盘真实间隙的设计方案进行了研究和探讨。
The photonic band gap (PBG) property of a one-dimensional photonic crystal with a defect layer under pressure is studied, accordingly an improved model of pressure sensor is described.
通过研究带缺陷的一维光子晶体受压力后光带隙性能的变化，提出了改进型光子晶体压力传感器的理论模型。
To research the power consumption of gas sensors, often the front-side of the sensor array has fabricated, the back-side of the sensor is etched to form an air gap between substrate and housing.
为了研制低功耗气体传感器，在传感器阵列上表面制备完成后，从下表面腐蚀传感器芯片的基底，以造成传感器芯片和封装室之间形成一个空气夹层。
The effects of dimensions of MHP, gas gap, and supporting beams on fabrication and working performance of the sensor are analyzed, and a new sensor structure with unequal beams is designed.
分析了微热板各层薄膜厚度、微热板下气隙高度、支撑桥尺寸、微热板面积大小对传感器加工、工作性能的影响，并结合实际工艺条件设计了一种采用不同支撑桥尺寸的传感器结构。
An enormous 0.025 "sensor gap reduces sensitivity to shock, vibration, and motor bearing wear."
一个巨大的0.025“差距降低灵敏度传感器的冲击，振动，和电机轴承磨损。”
Connecting the upper body using integrated design to ensure stability in the formation of welding, especially with the tool sensor and controller can be welded to the digital gap adjustment.
上部连接体采用一体化设计，保证焊接的平整稳定，尤其配合刀具传感器和控制器可以对焊接的缝隙进行数字化调节。
The capacitance formulae of a long cylindrical surface sensor with a gap are discussed by solving electric potential Lapalace's equation of the sensor.
通过求解带缝的长直圆柱面电容器中的电势的拉普拉斯方程，讨论该电容器的电容计算公式。
The sensor head is an interferometric based fiber optic senor in which the air-gap will change with the pressure or temperature.
传感头部分是基于干涉原理的光纤传感器，它的腔体长度会随着压力和温度发生变化。
There are many advantages for the new method of noncontact measurement employing the sensor for measuring piston ring end gap clearance dimension.
用其检测活塞环闭口间隙尺寸，是一种新的非接触式测量方法，具有许多优点。
The stress transfer model of the sensor is analyzed and the relationship between the change of Fabry-Perot gap length and hydrogen concentration is constructed.
分析了其应力的传递过程，建立了法布里-珀罗腔腔长变化与氢浓度关系的数学模型。
The stress transfer model of the sensor is analyzed and the relationship between the change of Fabry-Perot gap length and hydrogen concentration is constructed.
分析了其应力的传递过程，建立了法布里-珀罗腔腔长变化与氢浓度关系的数学模型。
应用推荐