Such a back-coupling, in which the position of the moving plate has an impact on the forces that move it, could produce complicated and varying motions.
在这种反向耦合中，移动板的位置对移动它的力有影响，可以产生变化的复杂运动。
Generally, the internal forces of shells are analysed by the plate elements, but because of the slope discontinuity of internal boundaries, it always influences the accuracy of the solution.
一般常用薄板单元分析薄壳内力，但由于内部边界联接斜率的不连续性而影响到求解精度。
The exact complex stress functions are obtained for a infinite plate with a centrical crack or semi-infinite crack under concentrated forces at a certain point.
对具有中心裂纹或半无限长裂纹的无限大板在集中力作用下得到了精确的复变应力函数。
According to the theory of a plate with large deflections, the motion responses equations of a floating plate are established considering the influence of the membrane forces.
根据板的大挠度理论，考虑板内的薄膜力，建立了波浪中运动平板的水弹性运动方程。
With the car upside - down, the ball forces the plunger to seat against the guide plate.
当汽车倾倒时，滚珠迫使柱塞落在支承板上。
Some documents show that the proposed method in calculating stiffness matrix is satisfied in solving the displacements and internal forces of plate by elastic theory.
有关资料表明采用这种地基模型计算地基刚度矩阵，所获板内力和位移结果能很好的符合弹性解答的基本规律。
The forces produced from the circular parallel plate, spherical and cylindrical capacitors were investigated by the calculation and determination criterion for elastic force.
采用弹力计算和产生弹力的判定方法，研究了圆平行板、球形和圆柱形电容器产生的弹力。
Such stress is reduced by increasing the bridging length, since the forces are distributed over a larger area of the plate.
该应力可通过增加桥接长度减小，因载荷分布于钢板更长区域。
The global latitudinal tectonic system is one of the important forces controlling the plate boundary and movement.
星球级纬向构造体系是控制板块边界和运动的重要的支配力量之一。
Nonlocking plates stabilize bone fragments against deforming forces by the use of friction between the plate and bone, generated by screws that compress the two surfaces together.
非锁定钢板通过螺钉导致的钢板和骨质之间的加压出现的摩擦力来抵抗畸形的力量从而未定骨折碎片。
The main driving forces for generating the fault structure pattern are the seafloor spreading of the South China Sea and the northward subduction of the Australian Plate.
形成这一构造格局的主要动力来自新生代以来南海的拉张作用以及澳洲板块南北向的推挤作用。
Conventional plating methods are based on the use of an adequate number of anchoring screws to press the plate against the bone with high compressive forces, creating a stable bone-implant connection.
传统钢板固定方法基于采用足够数量螺钉通过高压应力将钢板固定于骨面而产生稳定骨-内植物连接。
This paper gives an elastic analysis for an infinite plate weakened by an elliptical hole and being applied by concentrated forces and force couples.
文中给出了无限平板带椭圆孔又受集中力和力偶时的弹性分析。
Haskind discussed the non-steady motions of small curved planing plate by using the theory of complex functions, and obtained the general expression of hydrodynamic forces.
哈斯·金德用复变函数理论讨论了微弯滑行板的非定常运动，获得了计算水动力的一般公式。
This thesis analyzed static behavior of plate polyhedron frame structures. The distribution rule of member internal forces was found by comparing with plate grid structures.
本文分析研究了平板型多面体刚架结构的静力性能，通过与普通平板网架比较得到这种新结构杆件内力的分布规律。
The near crack line analysis method is used to investigate an eccentric crack loaded by shear forces in a finite plate, and the analytical solution are obtained.
利用裂纹线场方法对岩石材料偏心裂纹板受剪应力作用时进行了弹塑性分析，并且获得了理论解。
The authors, using the finite element method, analyse the rules of continuous deep beam internal forces under the influence of the support plate width.
作者以有限元法分析了连续深梁的内力受支座垫板宽度影响的变化规律；
The results showed that the spherical capacitor could produce the largest forces whilst parallel-plate capacitor smallest.
结果表明：球形电容器产生的弹力最大，平行板电容器产生的弹力最小。
Based on the formula for calculating the stress at the plate end of a rc beam strengthened by plate with arbitrary forces, the parameter analysis is presented.
在粘贴片材加固的混凝土梁的锚固端应力计算公式的基础上，对集中荷载和均布荷载作用下的梁进行参数分析。
In this paper, problems of bending of a thin plate under the action of in-plane forces are studied by using the method of multiple scales.
本文利用多重尺度法研究了薄板在中面力的作用下的弯曲问题。
This paper introduces a sort of damping material reducing vibration noise used for components suffered forces i. e. composite damping steel plate with asymmetrical structure.
本文介绍一种用于受力构件的减振降阻尼材料——不对称型复合阻尼钢板。
Taking advantage of folded-plate characteristic of transmitting forces spatially, the laying-out, section, reinforcing bars, and detail construction of slabs, beams, columns are designed.
利用该折板结构的空间传力特性，设计了结构板、梁、柱的尺寸、布置、配筋和细部构造。
Taking advantage of folded-plate characteristic of transmitting forces spatially, the laying-out, section, reinforcing bars, and detail construction of slabs, beams, columns are designed.
利用该折板结构的空间传力特性，设计了结构板、梁、柱的尺寸、布置、配筋和细部构造。
应用推荐