If the sensor is connected with a monolithic microcomputer, the fluid discharge can also be displayed.
若将此传感器与单片机连接，流体的流量也可显示出来。
Motor having electronic commutation, especially for driving fluid discharge device, particular in hair-dryer mounted such motor.
带有电子换向的电动马达，特别是用于驱动—排出流体的机器，尤其是装有这样马达的头发干燥器。
Fluid end consists mainly of module, suction and discharge valve assembly, suction and discharge spring, suction and discharge pipe, plunger, packing, safety valve and pressure regulator, etc.
液力端主要由液缸、吸入、排出阀总成、吸入、排出弹簧、吸入管、柱塞、盘根、安全阀、稳压器等部件组成。
Coupled with fluid equations for the electron and ion motion, the microwave discharge courses are calculated.
耦合电子、离子运动的流体方程，对微波等离子体的初始形成过程进行了数值模拟计算。
A generating well collects and generates the movement fluid from the discharge channels in the hydrocarbon layer.
和生产井，其设置为从烃层中汇合的排出通道收集和生产运动流体。
Experiment has showed that the uniformity of discharge of fast axial flow CO_2 laser can be improved by a multiple electrode system and a fluid introducing tude in front of the discharge tube.
实验表明，采用多电极和在放电管的入气端加一整流管能有效改善快速轴流CO_2激光器的放电均匀性。
Piping vibration or damage caused due to dynamic loads, such as mechanical vibration, acoustic vibration, fluid hammer, pulsation and relief valve discharge.
由于动荷载引起的管道震动和损坏，例如机械震动，声波震动，液击，压力脉动和泄放阀门泄放时引起的震动。
It has been verified in this paper, by theoretical analysis with two-phase fluid mechanics and hydraulic tests, that decreasing surface roughness in a wade stack can not increase critical discharge.
本文通过两相流理论分析和水力学试验验证证实：室内排水立管管壁粗糙度的减小，不仅不能加大其临界流量，反而会减小其临界流量。
In the alternating suction and discharge valve under the influence of pressure delivery and recycling to achieve the purpose of washing fluid.
在吸入和排出阀的交替作用下﹐实现压送与循环冲洗液的目的。
Gas (working fluid) from entering the spiral cavity suction tank by compression and exhaust through the exhaust orifice discharge cavity.
气体(工质)由吸气腔进入螺槽内，经压缩后通过排气孔口和排气腔排出。
A solar wafer slicing method was studied, which was based on complex dielectric fluid and efficiency electric discharge machining (EDM) and electric chemical machining (ECM) technique.
提出了一种基于复合工作液的、以电火花电解复合加工技术对太阳能硅片进行切割的工艺方法。
At the same discharge, flow shear rate of fracture fluid is high in the fracture of the thin layer, and its viscosity is low.
在相同排量下，压裂液在薄层裂缝中流动剪切速率高，粘度低。
A pair meshes mutually the gear and the fluid cylinder and discharge the suction chamber the cavity to separate.
一对相互啮合的齿轮和泵缸把吸入腔和排出腔隔开。
Fluid model was used to analyze the discharge process and the discharge efficiency of the driving pulse with different wave shapes.
本文采用流体模型，分析了多种驱动电压波形下，PDP的放电过程和放电效率。为选择合适的外加驱动电压提供帮助。
This paper illustrates the importance of cutting fluid for Electro-discharge machining. It introduces the development of a new cutting fluid DX-10, its application and its main characters.
概述了电火花线切割工作液的重要性，介绍了现有工作液——乳化液存在的缺点以及新型工作液DX-10的研制、主要特性、实验情况和推广应用前景。
It has been proved that the treatment of regular discharge of seminal fluid is of good treatment and prevention effect to the patients of the prostatic syndrome caused by separate living.
结论对诊断为分居综合征的患者采取规律排精具有良好的治疗和预防作用。
The piston is configured to draw fluid into the cylinder when moving in the first direction, and to discharge the fluid from the cylinder when moving in the second direction.
所述活塞设置为当沿第一方向移动时将流体抽入所述缸 体，当沿第二方向移动时将流体从所述缸体中排出。
The fluidizing characteristics and powder discharge process of gas fluid bed reactor with Hypol process were described.
介绍了聚丙烯流化床反应器流化特性和卸料过程；
The unique discharge port structure can prevent the cleaning fluid crystallization precipitation to plug the pipe.
独特的出料口结构可以防止清洗液析出结晶而堵塞管路。
The article analyzes the characteristic and the working condition of the cutting fluid using in electrical discharge machining (EDM).
分析线切割工作液的工作特点及工作状态，从生产实践中总结出科学合理选择使用工作液的方法。
A fixed height tension rib is arranged in the buffering damping cavity, and the edge is provided with a fluid fill-discharge valve.
它是在缓冲减震腔内设置了定高拉筋，边沿设置了流体充排阀。
The result shows two-phase fluid before shock wave is in the state of foam fluid and the exit discharge pressure reaches maximum when two-phase fl…
结果表明，汽液两相流在凝结激波前为泡沫流，在凝结激波后完全凝结成单相水的情况下，升压装置的出口压力达到最大值。
The result shows two-phase fluid before shock wave is in the state of foam fluid and the exit discharge pressure reaches maximum when two-phase fl…
结果表明，汽液两相流在凝结激波前为泡沫流，在凝结激波后完全凝结成单相水的情况下，升压装置的出口压力达到最大值。
应用推荐