Hot rolling testing of1050aluminium alloy developed saturation flow stresses at very large accumulated strains.
对1050铝合金进行了热轧试验，当达到很大的积累应变时，会产生饱和的流变应力。
Experimental results show that the flow stresses of the aluminum foams increase with increasing strain rate, demonstrating a distinct strain rate effect in the open-cell aluminum foams.
实验结果表明，通孔泡沫铝有明显应变率效应，随应变率上升，泡沫铝流动应力提高。
With proper design, the grain flow can be oriented in the direction of principal stresses encountered in actual use.
通过适当的设计，可以使晶粒流动方向与实际使用时的主应力方向一致。
From the plastic flow theory, the three-dimensional deformations and stresses of the deformation zone are formulated.
根据塑性力学流动理论，分析推导了变形区三维变形和应力的数学模型。
Analysis of bubble motion in the flow field was used to develop relations for the viscous stresses, turbulent stresses, and interfacial momentum exchange to close the model.
通过对气泡在流场中的运动和受力分析，给出了用以封闭模型的粘性应力、脉动应力、相间动量交换项的表达式。
The results of the measurement of Reynolds stresses and spectral analysis for a turbulent flow in a submerged air intake are presented in this paper.
本文给出了埋入式进气道内湍流流场的雷诺应力测量和频谱分析结果。
One of the greatest contributors to non-uniform hardness, increased thermal stresses, cracking and distortion is non-uniform fluid flow throughout the quench zone in production quench tanks.
造成淬火后工件硬度不均匀、热应力增加、畸变和开裂，主要是因为淬火槽内整个淬火区的液流不均匀。
The results depicted the temporal and spatial distributions of hemodynamic variables such as flow patterns, wall shear stresses and wall shear stress gradients.
结果展示了流场、壁面剪切应力及其梯度等血流动力学的时空分布情况。
This paper analyses the surface stresses on turbine's blade with experiment and calculating when turbine is working in flow field.
用实验和计算的方法对涡轮机叶片在流体场中的叶片受力面进行了分析。
The results show that the symmetrical model features with uniform distribution of flow patterns and wall shear stresses, ant it can improve the hemodynamics…
结果表明，对称搭桥术具有均匀的流动特征和壁面切应力分布，可以改善缝合区的血流动力学特性，并减少内膜增生和再狭窄的发生。
This paper introduced the basic principle of air vortex spinning and laid stresses on curl flow field in the air vortex twister, and the collecting and taking off of link fiber in air vortex spinning.
介绍了涡流纺纱的基本原理，对涡流加拈器中旋转流场的形成、纤维环的凝聚与剥取做了重点阐述。
Die-flow modeling has also been used successfully to study the stresses occurring at the die exit and to evaluate changes in die-exit geometry.
口模-流动模拟也被成功用于研究口模出口处出现的应力，以及评价口模-出口几何的变化。
Analysis of bubble motion in the flow field was used to develop relations for the viscous stresses, turbulent stresses, and interfacial momentum exchange to close...
通过对气泡在流场中的运动和受力分析，给出了用以封闭模型的粘性应力、脉动应力、相间动量交换项的表达式。
In a special circulating system with high velocity flow, boundary shear stresses in clear water flow, aerated flow and sediment laden flow are measured.
在高速水流循环系统中，用自行研制的剪切力传感器分别量测了清水、掺气水流及挟沙水流壁面上的剪切力；
U nder new stresses, a groundwater model can be divided into an initial flow field model and an appended flow field model .
在新增激发条件下，为便于问题的分析及模型的求解，可将模型分解为初始流场模型与附加水头场模型。
Then the normal Reynolds stresses in square duct flow are calculated using the new model and coefficient functions, the results are consistent with the experimental data.
最后用方截面管流中有关二次流的实验结果对模型进行鉴定。 结果表明，给出的模型在槽道流动和方截面管流中都获得了满意的结果。
The Simulation of Paper Suspension Flow and the Study on The Pulp Shear Stresses modeling in Headbox.
流浆箱内浆流模拟和浆料作用力的研究。
The Simulation of Paper Suspension Flow and the Study on The Pulp Shear Stresses modeling in Headbox.
流浆箱内浆流模拟和浆料作用力的研究。
应用推荐