If not, a specially designed tool will be used to pry apart the top and bottom flanges.
如果螺栓无法拆卸,将使用一种专门设计的工具把上下法兰盘撬开。
CCD flanges for resolution or imaging optimization.
优化成像质量或谱分辨率的两种CCD法兰盘。
Slip on flanges are not to be used in Hydrogen Service.
富氢环境中不允许使用活套法兰。
The engine-feed system interface is at the turbopump inlet flanges.
发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
The engine-feed system interface is at the turbopump inlet flanges .
发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
The gasket faces of girth flanges shall be machined after final heat treatment.
在最终热处理后翼缘法兰的垫片的端面应进行加工。
Class 250 cast iron and Class 300 steel flanges can not be used on these valves.
在这些阀门上不能使用250磅级铸铁和300磅级钢法兰。
Adjust windshield glass position until it is aligned with the flanges and adhesive.
调整挡风玻璃位置直至与凸缘和粘结剂对准。
This latter functional sulcus determines the extension limit of the denture flanges.
后者,也就是功能性沟决定了基托的伸展范围。
Casting parts, Machined parts, fasteners, flanges, stamped parts, well LIDS and the like.
铸造件,机加工件,紧固件,法兰,冲压件,井盖等。
Furthermore, the contribution of flanges to the shear resistance of the wall was analysed.
同时还分析了翼缘对墙片的抗剪承载力的贡献。
When installing the pipeline with flange, the gasket must be placed between the two butt flanges.
安装带法兰的管路时,必须在两个对接法兰的密封间放置垫片。
A. N. S. I. Standard b16.1-covers cast iron pipe flanges and flanged fittings (Class 125 and 250).
标准B16.1 -包括铸铁管道法兰和法兰连接件(125磅级和250磅级)。
Remove the old sleeve by bending the flanges at one end and withdrawing the sleeve from the other end.
要拆卸旧套管,要通过弯曲法兰的一端,然后将套管从另一端抽出来。
Rolling flanges should conform to Appendix A (standard appendix), and be selected according toTableA1, A2.
轧制法兰应符合附录A(标准的附录)的规定,并按表A1,A2选用。
Industrial pipeworks. Forged steel flanges and collars. Materials. Mechanical properties. Fabrication. Tests.
工业管道系统。锻制钢法兰和套圈。材料。机械性能。制造。试验。
Blend steel welding of flanges is allowed. Long neck flange should conform to related stipulations of GB 150.
法兰允许用钢板拼接焊制,对长颈法兰应符合GB 150的有关规定。
The roof rail and A-pillar are formed with a tubular body portion and longitudinally extending support flanges.
顶板横梁和A柱形成有管状主体部分和纵向地延伸的支撑凸缘。
The type, rating and facing of nozzle flanges shall conform to those specified in Purchaser's drawing or data sheet.
设备口法兰的类型、等级及端面应符合买方图纸或数据表的规定。
The method can be also applied to the stress analysis of a conical shell with uniform thickness connected with flanges.
本法亦可近似用于等壁厚锥壳与平法兰连接的应力计算。
When installing the Series 4700, it is recommended that galvanized steel back up rings be used behind the valve flanges.
在安装系列4700夹管阀时,建议在阀门法兰后面采用镀锌钢支撑环加固。
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
本阀可水平安装或垂直安装,安装时两法兰联接中间必须加密封垫片,然后均匀锁紧螺栓。
The support flanges are formed by pinching the blank during the hydroforming process to provide a double thickness flange.
在液压成形工艺期间,通过挤压坯料形成支撑凸缘,以提供双厚度凸缘。
Formation of protective films in highly recessed areas such as flanges and box sections provides critical corrosion protection.
电泳漆在非常隐蔽的部位,如翻边以及箱式结构,仍能形成完整的保护膜,从而得到较高的防腐蚀性。
The main deformation areas of the rectangular box in deep drawing were flanges and the circle-corners of female die in the corners.
盒形件拉深主要变形区集中在盒形件角部的法兰和凹模圆角部位。
During the process of analysis, concerning the stiffening action on the flanges by bolts, the application range of the joint is given.
在分析过程中,考虑了螺栓对法兰盘的加劲作用,并给出该类节点的使用范围。
Where process fluids could be abrasive, counter flanges shall be provided with detector body to prevent damage to the internal lining.
对于磨损工艺流体,应随传感器提供配对法兰以防损坏衬里。
Where process fluids could be abrasive, counter flanges shall be provided with detector body to prevent damage to the internal lining.
对于磨损工艺流体,应随传感器提供配对法兰以防损坏衬里。
应用推荐