To soft gaskets, flange surface too smooth adverse instead, because right now happened resistance smaller.
对软质垫片，法兰面过于光滑反而不利，因为此时发生界面泄露阻力变小了。
Interface leak So, gaskets are different, the requirements of the flange surface roughness is not the same.
所以，垫片不同，所要求的法兰表面粗糙度也不相同。
Therefore, the support foot and part of the flange surface were adjusted in situ, which solved the problem.
通过对烟道支腿及法兰面的局部现场调整，解决了此问题。
According to usage the top of flange surface minor faults proceed experiment and study, thought it do not affect HR H-beam.
通过对热轧H型钢翼缘端部表面瑕疵进行试验、研究，认为翼缘端部表面瑕疵不影响热轧h型钢的使用。
It can be used without sealing layers to provide an excellent sealing but there is a risk of flange surface damage especially at high seating pressure.
也可不带密封层直接使用，且能直到良好的密封效果，但在高压场合中容易对法兰的表面造成损失。
Flange surface roughness of the influence, especially sealing effect when using the soft cushion, seal surface coarse degree value big are caused by the leak is one of the main reasons why.
法兰表面粗糙度对密封效果影响很大，特别是当采用非软质垫片时，密封表面粗糙的度值大是造成泄露的主要原因之一。
The sensor shall be mounted on object surface, by fixation of screw thread or flange, and ensure firm contact with the equipment surface.
传感器采用贴面形式安装在物体表面，固定形式为螺纹或法兰，并确保与设备表面接触严密。
Caution: the sealing surface for the diaphragm on the top flange of the valve body receives special factory preparation to enhance sealing with PTFE diaphragms.
警告：用于阀体法兰上的隔膜的密封面在工厂受到特殊的处理，以强化聚四氟乙烯隔膜的密封性能。
For ease of installation, insert all flange bolts through the valve flange and then through the sleeve flange, but do not let the bolts extend beyond the surface of the flange rubber (See Figure 4).
为了使安装容易些，可以将所有法兰螺栓穿过阀门法兰，然后穿过套管法兰，但是不要让螺栓超过法兰橡胶表面(参阅图4)。
ANSI flange sealing principle is extremely simple: the two bolts each other extrusion flange sealing surface and form a seal gasket.
ANSI法兰的密封原理极其简单：螺栓的两个密封面相互挤压法兰垫片并形成密封。
Secondly, the flange gasket sealing ring has been replaced to ensure that the sealing face of sealing surface of the match.
其次，法兰垫片已被密封环所代替，以确保密封面对密封面的匹配。
Prior to startup, get rid of tape from labyrinth seal end of input shaft, labyrinth seal outer surface of output drive flange and respirator.
启动前应除去减速机输入轴迷宫密封端面和输出传动法兰迷宫密封外圆表面，以及呼吸器上的防锈包装及胶带。
The annular flange closely contacts the upper surface or underside of the table.
凸缘为环形结构，凸缘贴合在桌子上表面或者下底面。
Analysis is made on the dark lines defects occurring over the working surface of flange by measurement with the optical microscope, Scanning electro microscope (SEM) and electronic probe.
针对法兰盘加工面上出现的黑纹缺陷，采用光学显微镜、扫描电镜和电子探针等测试方法对其进行了分析。
The interfacial shear stress and peel stress between the FRP and the surface of tension flange were analyzed when the FRP was bonded to the tension flange of the bending members.
对受弯构件受拉翼缘外侧粘贴FRP后的界面剪应力和界面剥离应力进行了分析。
The flange sealing surface should be smooth and clean, to seriously clean up oil and rust during installation.
法兰密封面应平整清洁，安装时要认真清理油污和锈斑。
Using this device, the mechanical processing and fixing of flange sealing surface on the pressure vessels were simply and conveniently implemented on the spot.
该装置实现了压力容器法兰接口在现场进行简单、方便的机械加工及维修。
The aluminum housing includes a flange on the back of the unit for easy mounting to a flat surface.
铝制外壳，装置后部装有法兰，可轻松安装至平整表面。
A radial flange and in line with the bearing axis perpendicular to the bearing surface for the installation of a screw hole with a seat.
有径向凸缘及在与轴承轴心线垂直的支承表面上有供其安装用的螺钉孔的一种座。
Smooth surface only commonly used for low pressure, flange with soft qualitative thin gasket;
光滑面法兰一般只用于低压，配软质的薄密封垫；
All accessory interfaces should have protection covers with good sealing, there is no damage on the connecting screws and flange sealing surface.
组件所有外露接口均设有防护堵、盖，且封闭良好，接口螺纹和法兰密封面无损伤；
The reason why reducing the size of a compact flange, as a result of reduced diameter seals, which will reduce the sealing surface of the section.
紧凑法兰尺寸之所以减小，是由于减小了密封件的直径，这将会减小密封面的截面。
The wellhead cable penetrator is a kind of device for penetrating the tubing hanger and upper flange to connect the electric submersible pump and surface power at the production wellhead of ESP.
井口电缆穿越器是电潜泵采油井口上用于贯穿油管挂和上法兰，并连接电潜泵和井上电源的一种装置。
Sealed surface of gas valve, patrol machines, and installation flange.
煤气阀门的密封面，石油机械、管接头密封面、装配法兰等。
The method of surfacing welding sealing strip was adopted to repair the deformation of the flange joint surface of the high and intermediate pressure outer casing .
修理前，围绕兼顾解决焊接性、应力和变形问题，结合实际施工条件制定了以手工钨极氩弧焊、镍基焊丝、焊前低温预热、焊后锤击焊缝为要素的冷堆焊工艺。
The method of surfacing welding sealing strip was adopted to repair the deformation of the flange joint surface of the high and intermediate pressure outer casing .
修理前，围绕兼顾解决焊接性、应力和变形问题，结合实际施工条件制定了以手工钨极氩弧焊、镍基焊丝、焊前低温预热、焊后锤击焊缝为要素的冷堆焊工艺。
应用推荐