Describes a sleeve type compensator-the self balancing compensator, which can be used in heating networks to eliminate the blind flange force on primary fixing trestles.
介绍了一种套筒型补偿器———自平衡补偿器，它可用在热力管网中消除主固定支架的盲板力。
In such cases, a metal gasket also not applicable, because the requirements of the compaction force is too large, caused the bolts, make much deformation flange is not easy to seal.
在这种场合，金属垫片也不适用，因为这时要求的压紧力过大，导致螺栓较大的变形，使法兰不易封严。
Force transfer mechanism of the vertical stiffener joint model with only tensile beam flange is analyzed.
本文对外肋环板节点梁翼缘受拉模型的传力机理进行了分析。
Starting at the forward end of the upper molding, force the molding onto the door panel flange and continue rearward until it is completely seated on the flange.
从上部嵌条的前末端开始，用力使嵌条到车门饰板上并且继续向后直到它完全固定在凸缘上。
Based on divided flow method, the forging technology of near-net-shape deformation of the bushing with flange was optimized, the results show that this process reduces the forging force by 50%.
根据分流法原理，对带法兰汽车半轴套管近净锻造工艺进行了优化，优化后的工艺所需锻造力是优化前的50%。
The simulated thickness with separation force is smaller than that with blank-holder gap because the BHF is variable in the flange region.
采用分离力时的模拟厚度比压边间隙小是由于法兰区域的变压边力。
In such cases, the metal gasket does not apply, because then the pressing force required is too large, resulting in greater deformation of bolts, so difficult to seal flange.
在这种场合，金属垫片也不适用，因为这时要求的压紧力过大，导致螺栓较大的变形，使法兰不易封严。
V type packing structure has been employed to effectively transform the pushing force of the gland flange and the medium pressure into the sealing force against the stem.
阀杆采用V型填料密封结构，V型填料能将填料压盖的压紧力及介质力有效地转化成阀杆的密封力。
The device mainly consists of connection flange, brake disc, braking caliper, bracing frame, force-multiplier pump, hydropneumatic pipeline and proportional control valve.
该装置主要由连接法兰、刹车盘、刹车钳、支撑架、加力泵、液气管线和比例控制阀等组成。
The predetermined force loading device is composed of a loading flange, a bearing ring for positioning the axis, and an elastic washer arranged between the bearing ring and the loading flange.
所述的预定力加载装置由加载法兰、用于轴定位的轴承挡圈和在轴承挡圈和加载法兰之间的线弹性垫圈组成。
A circular model with an inward fixed flange was used for the support points, with a general shear force introduced to realize the constraint conditions at the hinges.
利用内边缘嵌固圆盘模型修正了支承点处的方程，并使用等效剪力实现了板边缘的位移协调条件。
The counter-force apparatus system which provides the counter force for the model is consists of model counter-force rack, flange plates and counter-force transferring plates.
反力装置系统用于给试验模型提供加载反力，主要包括模型反力架、法兰盘和反力传递板。
In this paper, a theoretical analysis for the local buckling of the flange plate of the partially encased concrete columns subjected to H-shape steel axis force was presented.
对部分包裹混凝土的H型钢轴压柱翼缘板的局部屈曲性能进行了理论分析。
Tests show that the cross section of the whole deck, working jointly as the lower flange of the main girder, should be taken for the calculated section subjected to longitudinal prestressing force.
试验证明，在纵向预应力作用下的计算截面应取道床板全部截面作为主梁下翼缘共同工作。
Molded Wide Arch Design. Greater Motion From Wider Arch. Less Force to Compress. Standard 150lb. ANSIB 16.1 Flange Drilling. Standard Face to Face Dimensions. Vacuum 26 "Hg."
模塑宽拱形设计。活动范围较大。需要的压缩力小。标准配置为150磅，ANSIB 16.1法兰钻机。真空26“百克。”
Molded Wide Arch Design. Greater Motion From Wider Arch. Less Force to Compress. Standard 150lb. ANSIB 16.1 Flange Drilling. Standard Face to Face Dimensions. Vacuum 26 "Hg."
模塑宽拱形设计。活动范围较大。需要的压缩力小。标准配置为150磅，ANSIB 16.1法兰钻机。真空26“百克。”
应用推荐