This paper carries on movement interference, finite element analysis and optimization design.
对模型进行了运动干涉检查，有限元分析和优化设计。
The finite element analysis and calculation of heat transfer in ablating bodies are presented.
本文采用有限元法，分析和计算了有热解的再入烧蚀体的传热问题。
Secondly:the thought of finite element analysis and the method using software named ANSYS are introduced.
其次：介绍有限元分析思想和模拟软件ANSYS的使用。
So it will markedly increase the efficiency of finite element analysis and optimization of the tooth profile.
显著地提高了对齿形进行有限元分析和优化的效率。
The finite element analysis and optimization design of piezoelectric intelligent beam was made based on ANSYS.
运用ANSYS软件进行压电智能梁结构的有限元分析和优化设计。
The finite element analysis and the experimental measurement for GYF-280 type high pressure re-actor were presented.
介绍了GYF-280高压反应釜有限元分析情况和实验测量结果。
This method can also be used to estimate the reliability of finite element analysis and dynamic design of automotive structures.
这个方法也可用于估计有限元分析和汽车结构动力学设计的可靠性。
The stress distribution of the, gearbox was obtained through finite element analysis and was compared with the experimental data.
通过有限元分析得到了该机匣的应力分布，并与试验值进行了对比。
By using ANSYS software as a development platform, finite element analysis and optimal design is made to some packing machinery parts.
以ANSYS软件为开发平台，对某包装机械的零件进行了有限元分析和优化设计。
The elastic_plastic fracture dynamic finite element analysis and the results of standard example indicate the procedure is believable.
通过算例的结果表明，编制的程序是可靠的。
Through the ug modeling, modification design on the structure, finite element analysis and interpretation of the die working reliability.
通过UG建模，修正设计的有关结构，有限元分析诠释了模具工作的可靠性。
The paper introduces two technology: finite element analysis and optimal design, which are often used in computer-aided engineering (CAE).
介绍了计算机辅助工程(CAE)技术中常用的两种技术：有限元分析和优化设计。
The nonlinear finite element analysis and model analysis for working mechanism are performed, and its result is validated by on-site strength test.
最后对该有限元分析模型的分析结果进行了生产实践强度的试验验证。
The lateral vibration of the high-speed rotating disk cutter slice blade was studied by the finite element analysis and the experimental measurement.
针对高速旋转圆盘刀具薄刀片实际工作时存在的横向振动问题，应用有限元方法及实验测量进行了研究。
Moreover, based on the method of finite element analysis and the general software, the failure behavior of high density syntactic foams is investigated.
还利用计算机和通用软件对高密度复合泡沫塑料进行了有限元分析，研究了高密度复合泡沫塑料的失效行为。
A capacitance sensor used for monitoring oil on - line is designed, and its structure parameters are made finite element analysis and orthogonal optimum.
设计了一种用于油品在线监测的电容传感器，并对其结构参数进行了有限元分析和正交优化。
For studying the deformation of flexible protection system accurately under the given impact, finite element analysis and performance test are carried out.
通过有限元仿真计算和现场性能试验，准确把握柔性防护网在规定的冲击能量作用下的最大变形数据。
Advance a new detection which associate with Finite Element Analysis and testing basing on testing of large hydraulic mechanical's fact press is true or not.
基于大型液压机实际压力是否达标的检测，提出了应用有限元分析和测试技术相结合的一种检测新方法。
This method takes advantage of the dynamic simulation function of finite element analysis and the thermodynamic theory to calculate the value of thermal flux.
该方法利用动力学分析功能，结合传热学原理求解热流传递数值；
Analysis and comparison between the finite element analysis and experiment results for stress intensity factor, limit load, and flexibility factor were performed.
从应力系数、极限载荷和柔度系数三个方面对有限元计算结果和试验结果进行对比分析。
Finally, research achievements offered by this paper have reference for the further non linear finite element analysis and design of reinforced concrete structure.
本文研究成果对进一步开展混凝土结构的非线性有限元分析和设计具有参考价值。
An automotive CAE software based on automotive theory, finite element analysis and optimization design has been developed to resolve relevant engineering problems.
基于汽车理论、有限元分析和优化设计方法，为解决工程实际问题，开发了汽车CAE软件系统。
In this paper, combining with the design of The Three Museums of Wuxi, the design, finite element analysis and joint experiment of cast-steel joint are introduced.
文章介绍了无锡博物院项目中铸钢节点的设计情况，铸钢节点的有限元分析及铸钢节点试验。
The cutter's design method, including parameter design and modeling, stress analysis and calculating, finite element analysis and correcting was introduced in detail.
详细介绍了铣刀的设计方法，包括参数设计与建模、受力分析与计算、有限元分析与校正。
In order to investigate the mechanical characteristics of the joint, finite element analysis and experimental research on the scale and full scale models are conducted.
为了全面了解该节点的受力性能，分别进行了缩尺模型和足尺模型的有限元分析和试验研究。
Properties of finite element analysis and its application to textile industry were discussed. Finite element analysis will broaden the research methods of textile science.
评述有限元分析技术的特点及其在纺织中的应用，指出有限元分析技术在纺织行业广泛的应用前景。
There are four post frame molding press and two kinds of structure, the fuselage uses finite element analysis and optimization design of the structure, reasonable structure.
成型压机有四柱和框架二种结构，机身采用有限元件结构分析和优化设计，结构合理。
There are four post frame molding press and two kinds of structure, the fuselage uses finite element analysis and optimization design of the structure, reasonable structure.
成型压机有四柱和框架二种结构，机身采用有限元件结构分析和优化设计，结构合理。
应用推荐