The FEM analysis was conducted with the simplified model.
对简化模型进行了有限元模拟分析。
The FEM analysis results agreed well with the test results.
有限元计算结果与试验结果基本一致。
The results of the theoretical and FEM analysis are compared.
理论计算结果与有限元分析结果被比较。
The character of jointed rocks is simulated by non-linear FEM analysis.
通过非线性有限元数值分析,完成了节理岩体力学特性的模拟。
FEM analysis is also performed to compute the stresses on the same points.
利用有限元软件建模和分析,得到测点位置的应力分析值。
The strains, stresses and displacements of all parts are gained based on the FEM analysis.
通过对钢包回转台的有限元数值计算,获得了各构件的应力、应变和位移等参数。
The Curved Surface Mesh Generation is one of important premise for the FEM analysis and computation.
曲面网格自动生成是有限元分析和计算的一个重要前提。
The paper also describes the application of the FEM analysis on the study of crankshaft reliability.
并阐述了有限元分析在研究曲轴可靠性方面的应用。
Methods 1223 nodes, 764 8-node hexahedron isoparametric elements and 3564 freedom degrees were used in FEM analysis.
方法有限元分析中采用了1223个节点、764个八节点六面体等参元和3564个自由度。
It is proved by FEM analysis that the proposed shape and structure of the test box can avoid resonance with the model soil.
在选定模型箱结构的外形与构造时,借助有限元分析论证了可不与模型土发生共振的箱体构造;
The FEM analysis of typical CFRD shows that this frictional model can well describe the failure process of peripheral joints.
文中用该模型对典型面板坝进行了变形分析,并对周边缝破坏的现象做出解释,表明所提模型合理可行。
Comparison between the FEM analysis results and the formula in related code showed that the formula gives conservative result.
并将有限元分析结果与规范相应公式的计算结果进行了比较,规范相应公式计算结果偏于保守。
The FEM analysis of creep has been completed to high pressure steam transforming valve used in 300MW electricity generating set.
对三十万发电机组旁路装置中高压蒸汽转换阀阀体进行了有限元分析,给出了十万小时后的蠕变位移、应变及应力。
The results obtained from the FEM analysis and the model test coincided very well, which showed that the FEM analysis is reliable.
试验结果与有限元分析结果吻合较好,表明有限元分析结果是可靠的。
The general elastic modulus of the dam is back analyzed by using the statistic model, hybrid model and the 3-D FEM analysis result.
应用统计模型、混合模型以及三维有限元的计算分析成果,反演了坝体的综合弹性模量;
Through FEM analysis, we found the problems existing in the structural design, and brought up the corresponding improvement suggestions.
通过有限元分析,发现了结构设计中存在的问题,提出了相应的改进建议。
FEM analysis of a kind BRB applicable to space structures was conducted by using software ANSYS. The hysteresis curve of the BRB was obtained.
利用ANSYS程序对一种适用于网壳结构的屈曲约束支撑进行有限元分析,得到支撑的滞回曲线。
Kinematic hardening model was used in FEM analysis and the response behaviors of transient local stress strain for material was also considered.
有限元分析采用了随动强化模型,并考虑材料瞬态局部应力应变的响应特性。
The verification data from both the test and the FEM analysis shows that the modified formula is in good agreement with the FEM analysis results.
通过试验数据和有限元分析数据验证,本文修正公式与有限元分析结果吻合较好。
Finally, temperature load caused by large fire was applied as node load to the lattice shell structure and non-linear FEM analysis was performed.
最后,将得到的升温情况分荷载步施加到大跨度网壳结构上,进行结构的非线性有限元分析。
Combined with the complexity of 3d FEM analysis of seepage field of underground project, the simulation of faultage was comprehensively discussed.
结合地下工程渗流场三维有限元分析复杂性的实际,对断层的处理进行积极探讨。
By employing FEM analysis software, the Eigen buckling of both a ring-stiffened cylinder and a ring and stringer-stiffened cylinder are calculated.
本文中利用有限元软件对环肋圆柱壳和纵横加筋圆柱壳进行了特征值屈曲分析。
The construction of the general OOFEM framework model is very important for studying nonlinear FEM analysis algorithms and parallel FEM algorithms.
面向对象的有限元(OOFEM)通用框架的构造对于有限元算法和并行有限元的研究具有重要意义。
The temperature load was then applied as node load to the lattice shell, which is the roof structure of the warehouse, and FEM analysis was performed.
将温度场以节点荷载的形式施加到网壳结构上,进行有限元数值分析。
The solid modeling system is subsidiary to "Boiler CAD Application System". 3D Solid modeling is basis of FEM analysis and pipe line interference check.
锅炉三维造型系统是锅炉CAD应用系统的子系统,三维实体建模是进行有限元分析和空间管路干涉检查的基础。
Work behavior of composite foundation of cemented soil pile is studied by 3D non-linear FEM analysis applying post-peak softening model of cemented soil.
考虑水泥土峰值后软化性能对水泥土桩复合地基性能进行了三维非线性有限元分析。
All the model parameters can be easily determined. The equivalent numerical model was applied to two and three dimension FEM analysis of a practical CFRD.
采用该模型对某面板堆石坝应力变形进行了二三维有限元分析,并与原状模拟分析结果进行了对比。
The latter part made FEM analysis on a muzzle brake and a cradle of some type with the use of I-DEAS. The maximal load value and its location were produced.
后一部分利用I-DEAS软件对某一型号的炮口制退器和摇架进行了有限元分析,求解了所能够承受的最大载荷以及最大载荷位置。
This paper deals with the mechanical model from FEM analysis and the structural optimum design, which can be computed by means of the program system DDDU-2.
本文探讨了某特种车车身的有限元分析和结构优化设计的力学模型,利用DDDU - 2程序系统进行了计算。
The applicability of the restriction-equations method in smooth structures, cylinder with fixture fringe and shell with fixture seat is validated by FEM analysis.
通过有限元算例分析,验证了约束方程连接的体壳连接方法在平板结构、带安装边的圆壳结构以及带安装座的壳结构上的适用性。
应用推荐