The higher the feed temperature is, the larger the hydrochloric acid concentration in the distillate would be.
随着料液温度的升高，蒸馏液中盐酸浓度增大；
Results of VMD experiments indicate that flux increases when feed temperature, feed rate and vacuum degree increase.
实验表明，随进料温度、进料流速、冷侧真空度的增大，膜通量增大；
The separation factor increases as the feed flow rate and downstream pressure increase, and decreases as the feed temperature increases.
同时流速提高，温度降低，以及增大冷侧压力，分离因子增大。
Usually connected in series to maintain the tube in the sterilizer after the feed temperature of 90 degrees Celsius, the specific access method, please refer to flow chart.
通常是串接在杀菌机的保持管后，进料温度摄氏90度左右，具体接法请参考工艺流程图。
The unit of IPL Purify in IPL circulation system was calculated and analyse . Feed temperature is consequential to effect of extract and vapor flux of reboil is marked to the stripper.
对无机循环系统的无机工艺液净化单元进行了工艺参数分析，定量的分析了进料温度和进料量对萃取塔萃取效果的影响，以及再沸器蒸汽流量对汽提塔分离效果的影响。
Additionally, a dynamic model was proposed to describe the process of batch operation with a constant feed temperature, and its prediction agrees tallied well with the result of our experiment.
同时建立了动态膜蒸馏过程的数学模型，模型预测值与恒温间歇操作实验结果吻合较好。
The effects of the feed composition and the feed temperature on the energy-saving efficiency of the backward-feed two-effect distillation are researched in ethanol-water system by process simulation.
以乙醇-水为物系，通过模拟计算，研究进料组成和进料温度对三种逆流双效精馏节能效果的影响。
As a processor, the only way you can maximize feed-throat performance is to adjust its temperature.
作为一个加工者，优化喂料口的唯一方法就是调整它的温度。
Should stand in the side entrance operation. First open water valve to send to the temperature reached e. reascularization gas. Ignite in and out of the oven gas rear can feed.
应站在入口的侧面进行操作。先打开水阀再送电，待炉温达到规定值再通入煤气。点燃进出炉口煤气后方可进料。
Whisper with you when you sick, I will try the temperature before feed you the medicine. draw your hand front the bed.
你生病的时候轻声和你说话，喂你吃药先试试水温，在你床前拉着你的手；
To subdue the temperature rise, several means meliorating feed condition of grinding fluid in the grinding area are used.
为了抑制磨削中的温升，采取了改善磨削区磨削液供给状况的几种措施。
This energy will be used to feed some sensors which measure for instance the temperature, the level of the water, and then transmit this information to a remote control panel where it can be used.
能源会被使用在供温度，和水位测量的感应器上，之后会转化这个资讯，到遥控器上被使用。
The effects of the feed rate of air, steam and coal on bed temperature, gas composition, calorific value, carbon conversion and gasification efficiency are predicted and analyzed with the model.
在此基础上，还就空气加入量、蒸汽加入量及加煤速率对床温、煤气组成、煤气热值、碳转化率和气化效率的影响做了预测和分析。
The stability of the catalyst could be improved by increasing the reaction temperature or by lowering the reaction pressure and the concentration of oxygen in the feed.
考察了不同反应条件对催化剂稳定性的影响，发现降低反应温度、提高反应压力和进料中氧气浓度可在一定程度上提高催化剂的稳定性。
The effects of tool's inclination angle on chip formation and the temperature fields, as well as the cutting forces, back forces and feed forces are discussed.
通过三维切削模拟可以获得在不同刃倾角精密切削过程的条件下切屑形状、切削力和切削温度场的分布情况。
This paper studies the influence of extrusion temperature. Screw speed, feed speed and water content on starch gelatinization depolymerization, soluble index and expansion efficiency.
研究了挤压过程中，挤压温度、螺杆转速、进料速度、原料水分含量对淀粉的糊化、降解及对挤出物的溶解指数和膨化度的影响。
Under control of the outlet temperature and the pressures, the increase of feed throughput will cause the decrease of gas, gasoline and coke produced in reaction.
再生器压力、沉降器压力和提升管反应器出口温度均被控制，原料处理量提高后，气体、汽油和焦炭产率均下降。
It was found that the neodymium oxide content in neodymium carbonate increased with adding temperature increasing and decreased with the feed molar ratio increasing.
结果表明：随着结晶陈化温度的提高，结晶碳酸钕中氧化钕含量升高，而增大碳酸氢铵加入量则使氧化钕含量降低。
The causes behind breakage of the catalyst are excessive sodium and vanadium content in the feed oil, excessively high regeneration temperature and excessively high steam velocity in riser pipe.
对催化剂的分析表明，催化剂破碎主要由于原料中钠、钒含量超标、再生温度过高和提升管预提蒸汽线速过高所致。
Effects of pressure, temperature, initial feed concentration of HMX solute, expansion speed of solution and growth of crystal on the GAS process have been studied.
型HMX微细颗粒。考察了压力、温度、溶液初始浓度及溶液膨胀速率对GAS重结晶过程、晶粒大小和晶型的影响以及晶体的增长。
Effects of emulsifier types and amounts, polymerization temperature and feed methods on particle size, stability of latex and water proofing property of films were investigated.
探讨了乳化剂种类和用量、聚合温度及加料方式对乳胶粒大小、胶乳稳定性和胶膜耐水性的影响。
The effect of the various factors, which is the structure and size of the pore, pressure, temperature, and feed composition is investigated in detail.
综述了气体混合物通过炭膜时传递和分离性能的影响因素（如孔结构及孔径大小、操作压力、温度、组分组成等）；
With the cooperative control of drawing temperature and feed speed, the final hole structure can be effectively controlled by tuning the applied pressure.
在温度和送料速度的协调控制下，通过调节气压参数可有效控制气孔结构。
The distribution of temperature, flow, and concentration were significantly influenced by the composition of gas feed.
塔内温度、流率、浓度分布受原料气组成的影响较大。
The effects of the feed ratio of raw materials, reaction temperature and the dosage of catalyst, etc factors on the new synthesis process of brominated epoxy resin for copper clad panel were studied.
研究了原料配比、反应温度、催化剂等因素对覆铜板专用溴化环氧树脂合成新工艺的影响。
Probiotics as feed additives has been widely used in the production practice. But the added feed pelleting temperature, probiotics pressure on the activity of a bigger had lossed.
益生菌作为饲料添加剂在生产实际中已被广泛应用，但是添加饲料的制粒温度、压力会对益生菌的活性造成较大损失。
Place the cap on the bottle and shake to dissolve powder. Before feeding, check the feed is at the right temperature by shaking a few drops on your wrist.
盖上奶瓶盖，摇动融化奶粉。喂哺前先滴几滴在手腕上，检查温度是否合适。
Many factors which may affect the catalytic behavior such as rare earth metal species, calcination temperature, reaction temperature, space speed and feed gas purity were studied.
并研究了不同稀土金属，不同焙烧温度，不同反应温度，不同空速条件及不同来源氢气等因素对催化性能的影响。
Before feeding, check the feed is at the right temperature by shaking a few drops on your wrist.
喂哺前先滴几滴在手腕上，检查温度是否合适。
Before feeding, check the feed is at the right temperature by shaking a few drops on your wrist.
喂哺前先滴几滴在手腕上，检查温度是否合适。
应用推荐