Plug in to the Live Mesh news feed system to generate notifications for key activities in your application.
接入LiveMesh的新闻订阅系统，来为你的应用程序中的关键活动生成提醒。
High-speed feed system is one of the key technologies for high-speed machine tools.
高速进给系统是高速加工机床的关键技术之一。
The measured results indicate that the feed system achieves the design goal, and the measured results agree well with the theoretical results.
测试结果表明，所设计的馈源达到了设计要求，理论计算结果和实验测试数据吻合良好。
Injection mould feed system is an important component of the structure design of injection mould, and is also the only channel for molten plastic flowing into mold cavity.
浇注系统是注塑模具结构设计中的一个重要组成部分，也是塑料熔体进入模具型腔的唯一通道。
The practice result shows that this servo-feed system can realize servo moving accurately, and can meet the system position accuracy, response speed and stability required by the machining process.
经实际生产验证，该伺服进给系统能准确地实现伺服运动，满足加工过程要求的系统定位精度、响应速度及稳定性。
The engine-feed system interface is at the turbopump inlet flanges.
发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
The engine-feed system interface is at the turbopump inlet flanges .
发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
Servo drive for film feed system allows for accurate positioning and easy adjustment.
送膜机构采用伺服电机，定位精度高，易于调整。
The design of a kind of jet mixture used in material feed system was discussed in this paper.
给出了一种可应用于非标准给料系统的引射式风粉混合器的设计。
Finally the authors prospect the development direction of feed system in high-speed machining.
最后展望了高速加工中进给系统的发展前景。
Technical innovation is done for feed system of cracking furnace for adapting various feedstocks.
为适应各种原料，对裂解炉进料系统进行技术改进。
The direct drive feed system by linear motors is an ideal solution to realize the high-speed system.
直线电机驱动的进给系统是实现数控机床进给高速化的新形式。
The slurry feed system offers the only continuous feed possibility of the three methods investigated.
煤粉浆加料装置是所研究的这三种加料方法中唯一可能实现连续加料的一种方法。
The causes of SH and RH tube explosion and coal feed system jamming in the operating CFBB are analyzed.
分析循环流化床锅炉运行中出现的高温再热器、二级过热器爆管和给煤系统旋转给料阀经常堵煤等问题。
To analyze the creeping phenomenon in theory by modeling the feed system and educing the vibration equation.
通过对进给系统建立运动模型，导出振动方程，并对爬行现象进行了理论分析。
Selection and calculation of ball-screw pairs in the design of feed system in CNC machine tools was introduced.
本文较详细地介绍了数控机床伺服进给系统中滚珠丝杠副的选择与计算。
The design of the linear feed system of an overhead gantry high speed machining center is presented in the paper.
介绍一种高架桥式高速加工中心直线进给系统的设计。
Double shaft servo feed system by PLC to control accurately and automatically feed of cylinder head and valve lift.
PLC控制双轴伺服进给系统，精确自动控制缸盖进给和气门升程。
Rigidity of feed system with ball screw in nc lathe has a major influence on loss of momentum and positioning precision.
数控车床丝杠进给系统刚度对系统的失动量和定位精度影响较大。
It is possible for the feed system to have a low impedance, looking downstream from the pressure source at a certain frequency.
在压力源下游，供应系统在某一频率下可能有一低的阻抗。
The feed system of high-speed precise machine tool directly driven by linear motor is one kind of perfect driving method to the system.
直线电机直接驱动方式是高速精密机床进给系统的一种理想驱动方式。
The excellent dynamic characteristic function wire feed system driven by a permanent-magnet DC moment motor is described in this paper.
本文介绍了一种永磁式直流力矩电机驱动的动态品质优异的函数送丝系统。
Provide flexible shaft (tungsten tungsten wire rope), molybdenum, molybdenum seed chuck hammer, molybdenum, molybdenum tube two feed system.
提供钨软轴(钨丝绳)、钼重锤、钼籽晶夹头、钼导流筒、钼二次进料系统。
This paper designs a S-band feed system for HPM antenna, which consists of a dual-mode conical horn and a rectangular-circular mode convertor.
本文设计了一种S波段高功率微波天线的馈源系统，该系统由双模圆锥喇叭和矩-圆模式转换器两部分组成。
This thesis mainly studies how to design the structure of heavy NC machine tool's feed system which is developed by QIQIHAR heavy CNC Equipment CO.
本文针对齐齐哈尔重型数控设备股份有限公司的重型数控机床进给系统的结构进行合理化设计，并提出一种快速有效的机床设计方法。
At last an example of enunciator crust design is given to present the basic flow and method of the intelligent design of injection mould feed system.
最后以报警器壳体塑件为例，给出了应用开发的智能化设计系统进行注塑模具浇注系统设计的基本流程与方法。
This paper analyzed AC servo heavy cutting feed system component parts and their actions, and built model about mechanical transmission equipment section.
分析了强力切削交流伺服进给系统各组成环节及作用，对机械传动装置部分建立了模型。
So the research on the injection mould feed system design technology and method is becoming one of the important facets in the field of the injection mould CAD.
因此，浇注系统设计技术与方法的研究，成为注塑模具CAD技术研究与开发的重要内容之一。
So the research on the injection mould feed system design technology and method is becoming one of the important facets in the field of the injection mould CAD.
因此，浇注系统设计技术与方法的研究，成为注塑模具CAD技术研究与开发的重要内容之一。
应用推荐