FEA model of its free status has been built using ANSYS APDL.
使用参数化建模方法,建立钢板弹簧自由状态下的有限元模型。
Based on the silicon thermal flow sensor, a FEA model is given.
基于作者所在实验室研制的硅热流量传感器,给出了其有限元模型。
FEA model build and computational plate forming for polymer seals product.
针对聚合物密封件建立有限元模型,进行计算单元划分。
The simplified model was validated by its comparison with the key responses of the detailed FEA model.
通过与原详细有限元模型的关键响应量对比,证明了简化模型的准确性和有效性。
The FEA model was parameterized by APDL language and the stiffness distribution was computed over the workspace.
通过APDL语言实现有限元模型的参数化设计,计算出并联机床在工作空间内的刚度分布。
When FEA model was formed, the quadratic singular elements of the tip of the crack were formed by node to element.
在建立有限元模型时对于裂纹尖端的单元,采用节点—单元的方式生成二次奇异单元。
We used periodic symmetry constraint on FEA Model. Elastic plastic finite element principle used in analysis process.
用弹塑性有限元法分析超速预过载处理后叶轮的残余位移、应变及应力场 ,给出相应的求解结果。
For the cracking on the chassis of DLQ25A movable crane, the ANSYS program is used to establish the shell-elements FEA model of main beam with supporting leg.
针对DL Q 2 5 A轮胎起重机底架结构开裂的情况,采用ANSYS程序建立了主梁与支腿一体的板壳单元有限元分析模型。
Based on the FEA model of the tank gear box, by using the rigid-flexible model technology, the structure strength of the gear box under the typical condition is tested.
在所建立的某型坦克齿轮传动箱箱体有限元模型的基础上,利用刚柔体耦合技术,对坦克传动箱在典型工况下的结构强度进行了虚拟考核。
Secondly, an FEA model is built, in which the plate offset effect is considered for the tank walls of variable thickness, and the effect of the seismic load is analyzed.
在有限元计算模型处理时,对由不同厚度钢板焊接而成的罐壁进行了板壳元的厚度偏移处理,并详细讨论了地震载荷的计算和影响。
Furthermore, by the 2-d FEA model, the effect of the reduction of the surface settlement due to different distances of recharge or the depth of water-sealing was studied.
同时通过建立二维有限元模型,研究了工程上采用的回灌和止水措施对减小地表变形的作用。
The FEA model of prestressed cylindrical receptacle is built, and it shows contact element can be applied to simulate shrink-fit by the comparison with theoretical solution.
建立了预紧圆挤压筒有限元分析模型,通过和理论解的比较论证了接触单元法模拟过盈装配的可行性。
The FEA model of prestressed cylindrical receptacle is built, and it shows contact element can be applied to simulate shrink-fit by the comparison with theoretical solution.
建立了预紧圆挤压筒有限元分析模型,通过和理论解的比较论证了接触单元法模拟过盈装配的可行性。
应用推荐