The deficiency of present belt drives design criteria is pointed out to get a start in sliding failure and fatigue fracture failure.
从防止带传动打滑失效和疲劳断裂失效出发，指出现有带传动设计准则之不足。
Single pipe pile shows sliding failure at interface and cannot utilize the strength of material; the bearing capacity and deformation ability are low.
结果表明，现行的单钢管桩属于界面的粘结破坏，承载力低，变形能力弱，不能充分发挥材料特性。
If the true dip line of one or two joint planes plot within a sliding zone of double-faced slope, a double-faced sliding failure can be possible.
如果有一两个节理面真倾向线落在滑动区内，滑动破坏才可能发生。
A certain large gently inclined cut slope was destructed by its rock slope failure due to top soil sliding.
某大型缓倾陡节理路堑边坡，在上部薄表土滑动作用下岩质坡体倾倒破坏。
Methods Based on the two failure mode of plane and wedge sliding destruction of the limit equilibrium theory, rock slope stability is analysed.
方法按极限平衡理论中的平面滑动破坏和楔体破坏两种破坏模式进行稳定性分析。
Through the engineering practice, the bedding failure mechanisms of bedded rock side-slope could be divided into three types: plane rotatory sliding, disintegration sliding and gradual destruction.
通过工程实践，将层状岩体边坡顺层破坏机理归纳为三方面的问题，即：平面旋转滑动、解体滑动和渐进破坏。
Wear failure refers to the relative sliding friction between the surfaces causes the surface of the metal continue to wear their work arising from the failure.
磨损失效系指表面之间的相对滑动摩擦导致其工作表面金属不断磨损而产生的失效。
The main failure patterns of the sliding bearing of a cone bit are gluing and abrasion.
钻头滑动轴承的主要失效形式是胶合和磨粒磨损。
As a specific instability of rock slope, an antidip stratified rock slope is different from the sliding one, and the failure mechanism has not been clarified yet.
作为一个具体的岩质边坡不稳定，反倾层状岩质边坡滑动不同，失效机理尚未完全阐明。
This method presented the criteria for the acceleration of failure by slope-sliding and was able to do inverse computation of parameters of mechanics on slide surface.
该方法给出了滑坡破坏加速度判据并能够精确反算滑动面力学参数。
The damage form of micropiles can be defined as cutting and bending failure near the sliding face.
试验中所用微型桩的破坏模式为滑面附近的弯曲与剪切相结合的破坏。
To ensure the security of this joint, interracial sliding of the joint, tensile failure of the bolts and extruding failure of the interfaces must be prevented.
指出为保证该联接安全可靠，必须满足轴承座底面与游梁接合面间不滑移、螺栓不拉断、接合面不压溃及轴承座不翻转等条件。
Based on the limit equilibrium theory and the hypothesis of planar sliding surface, a formula for calculating the Angle of shear failure was deduced considering cohesion and cut slope Angle.
基于极限平衡理论及平面滑裂面假定，在考虑土黏聚力及放坡角度的基础上，推导了平面滑裂面剪切破坏角的数学表达式。
This method presented the criteria for the acceleration of failure by slope-sliding a…
该方法给出了滑坡破坏加速度判据并能够精确反算滑动面力学参数。
This method presented the criteria for the acceleration of failure by slope-sliding a…
该方法给出了滑坡破坏加速度判据并能够精确反算滑动面力学参数。
应用推荐