The failure of machine taps arises frequently from excessive or premature wear.
过度或早期磨损是机用丝锥常见的失效形式。
There is some of the fuzzy on the defining standard of failure because the abrasion failure of machine facility is a consecutive and gradually failure.
由于机械设备的磨损失效是一种连续的渐发性失效，因此在判别失效准则上存在着模糊性。
This usually results in a failure of a product, which leads to skepticism from the market and delivers a blow to the integrity of Machine Learning technology.
通常，这会导致产品出故障，引起市场怀疑，对机器学习的完整性造成打击。
If clones are distributed to various nodes in the system, even the failure of an entire machine does not produce devastating consequences.
如果克隆分布于系统内的各个节点，即便是整个机器的故障也不会产生灾难性的后果。
Restarting may be needed after a planned shutdown, after an unplanned machine failure, or in order to replay a model event of scientific interest with a different time step granularity.
重新启动可能需要在计划关机之后，计划外机器故障之后，或者在使用不同时间步骤粒度重放科学模型事件时。
But because the machine USES a lot of electricity and is prone to failure, Spotz will run it for only 20 minutes every other day.
但由于海水淡化设备要消耗大量的电，并很容易发生故障，斯伯茨只能每隔一天让它运行20分钟。
Each machine is prepared to take over the workload of its partner in the event of a failure.
每个机器都准备在出现故障时接管其伙伴的工作负载。
Machine 2's workload fails over to machine 1 in the event of a failure and vice versa.
在出现故障时，机器2的工作量会故障转移到机器1中，反之亦然。
When a failure of the server in the cluster occurs, the hot standby server takes on the load of the failed server machine in addition to the work that it was performing during normal operations.
在集群中出现服务器故障时，除了在正常运作期间执行的工作以外，热备份服务器还承担故障服务器的负荷。
Machine failure has to be expected, so it's crucial that your data can be backed up and restored in case of failures.
计算机难免会出现故障，所以必须能够备份数据并在发生故障时恢复。
In the event of a second failure, the application precedence on the spare machine is as follows: Maximo, then eCMDB, followed by IC.
在出现第二次故障时，空闲机器上的应用程序优先级如下：Maximo，然后是eCMDB，最后是IC。
Each machine in a LoadLeveler cluster performs one or more roles in scheduling jobs. These roles and the implications of their failure are as follows.
在作业的调度中，LoadLeveler集群的每一台机器都要扮演一个或者多个角色。
Hidden failures can be early found and maintenance cost can be cut through the monitoring of machine status and the use of failure diagnostic technique.
通过对机器状态的监测及故障诊断技术的应用，可以及早地发现事故隐患，减少维修成本。
This testing machine is good at studying the deformation and failure of inhomogeneous and discontinuous media from the Angle of loading equability.
该试验装置可以更好地从均匀加载的角度研究非均匀，非连续介质的变形及破坏规律。
The failure curve of the horizontal machine center during the forepart fault is degressive, the internal time is Weibull distribution.
卧式加工中心在早期故障期时，故障率曲线为递减型，间隔时间服从威布尔分布。
The meaning to identify the vibration of electric machine, the relationship between the vibration and the failure diagnose, the monitoring principle and monitoring means of vibration are discussed.
讨论了识别电机振动的意义、电机振动与故障诊断的关系、振动监测原理和监测手段。
It is impossible to assess the importance of a machine of this sort, for many international misunderstandings are caused simply through our failure to understand each other.
这类机器的重要性是无法评估的，因为许多国际间的误会均由彼此语言不通所致。
Fault diagnosis for rolling bearing is an important part of machine failure diagnosis.
滚动轴承故障诊断是机械故障检测中一个重要方面。
It is difficult to find the causes of failure for the mechanical fault maintenance of CNC machine.
数控机床机械故障维修的难点是查找故障产生的原因。
Failure of the machine may be caused by the rupture of the triangle belt.
这台机器的故障可能是由三角带断裂引起的。
Considering the complex influence factors for the failure of drill stem, an analytic model for failure of drill stem based on support vector machine and cluster analysis theory was established.
针对钻具失效影响因素比较复杂的问题，建立了基于支持向量机和聚类分析理论的钻具失效原因分析模型。
The iron spectrum is not only used in the study of wearing, but also to monitor the failure of construction machine.
基于微粒分析的铁谱技术不仅可以用于磨损机理的研究，而且能对机械设备进行监测和故障诊断。
Fault diagnosis for rolling bearing is the important part of machine failure diagnosis. Resonance-demodulation is one of available methods for gear failure signal diagnosis.
滚动轴承故障诊断是机械故障检测中一个重要方面，共振解调是一种有效分析滚动轴承故障信号的方法。
In this paper we give a general formula on the reliability calculation in the case of that failure modes of machine components are correlated according to the reliability designing theory.
根据可靠性设计理论，给出了失效相关的机械零件可靠度计算的通用公式。
Tracing failure and undersampling are frequently emerged when the two dimensional tracing and measurement function of commercial Coordinate Measuring Machine software is applied.
商品坐标测量机软件的二维曲线自动跟踪测量功能在应用中经常出现跟踪失败和采样信息不充分等问题。
The failure phenomenon of reference point of NC machine was mainly introduced in the paper, and its reasons were analyzed, an idea and solution were given.
本文主要介绍了数控机床回基准点的故障现象，并对其进行分析，给出了具体解决的方法和思路。
In this paper, detail analysis of failure maintenance to Panasonic auto-mounting machine is given, and a few examples of failure diagnose to explain how to solve the problem are introduced.
本文对松下自动贴片实装机的故障维修进行详细的分析，并结合几个实例说明故障诊断的过程。
The reasons and general way of failure diagnose and preventing measures of hydraulic pressure in machine tools were expounded. And the three examples were specially analyzed.
阐述了机床产生液压冲击的原因、诊断方法、危害及预防措施，并通过三个实例作了详细分析。
The failure of force connecter of runner disturbs seriously the stability or turbine machine.
而转轮接力器如出现故障，则严重破坏机组运行的稳定性。
Based on study and analysis of the failure and monitoring technology of CNC machine tool, and the methods about predictive maintenance were established.
通过对数控机床的故障及有关的设备故障诊断技术的分析和研究，提出了数控机床的预防性保养的方法。
应用推荐