The tensioning of the cables is finished and the error is controlled in 5%, which verifies the correctness of the construction simulation.
钢索张拉顺利完成，最终误差控制在5%以内，证明了施工模拟分析的正确性。
The result indicated that the model's short-term prediction error is controlled with 5%, which conforms with the financial appraisal requirements.
预测结果表明，模型的近期预测误差控制在5%以内，完全符合财务评价要求。
For the case of planar interception, the so called relative heading error angle between the relative velocity vector and the LoS (Line of Sight) is chosen as the output to be controlled to zero.
针对平面拦截问题，选择导弹和目标之间的相对速度矢量与导弹-目标视线之间的夹角（称为相对航向误差角）作为将要被控制到零的输出。
The prediction results show that the error of accuracy prediction can be controlled within 10% by using the proposed model, which is of excellent capability of accuracy prediction.
利用该模型进行的精度预测结果表明，该模型的预测误差可以控制在10 %以内，具有很高的精度预测能力。
Aim To reduce the error of the valve controlled system with energy saving hydraulic pump, which is caused by variable gain characteristic.
目的减少由于节能液压源下的阀控系统变增益带来的跟踪误差。
In this paper, a neural network controller is designed for ash content control of papermaking process, neural networks are trained by using the output error of the controlled plant directly.
对于非线性，大时延、变参数的造纸过程灰份含量的控制，本文给出了一种神经网络控制方法。
Both the theoretical analysis and the experimental research show that not only the control principle is feasible but also the flow-division error can be controlled within 1%.
通过理论分析和控制原理可行性实验研究，证明该阀的控制原理完全可行，而且可使分流误差初步控制在1%以内。
An error distribution of the controlled error is then determined based on a sync layer protocol and the detected error in the multimedia data is concealed based on an application layer protocol.
然后，根据同步层协议来确定所述受控错误的错误分布并根据应用层协议来隐匿所述多媒体数据中所检测到的错误。
The opening parachute signal is required to sent on the fixed height when the vehicle reentry. The height controlled error through axis apparent acceleration can not meet the required precision.
弹道式飞行器再入时，常常要求在规定高度上发出开伞信号，过载延时控制方法误差太大，不能满足精度要求。
The system showed satisfactory result when tested by Dalian University of Technology Auto Electronic Factory. The error between program controlled data and actual data is acceptable.
该系统通过了大连理工大学汽车电子公司的实验测试，所得程序控制数据与实际控制数据的误差相当小，效果十分理想。
The experimental result indicated that the reconstruction error of QMF Banks after optimization is controlled in 2%, indicates this method the validity.
实验结果表明，优化后QM f组的重建误差控制在2%以内，表明该方法的有效性。
A new variable step-size CMA blind equalization algorithm is introduced to conquer the defects of CMA, in which the step size is controlled by the estimation of error signal's autocorrelation.
提出了一种自适应变步长恒模盲均衡算法，利用剩余误差信号的自相关函数估计值作为控制步长的因子来自适应改变步长的大小，克服了恒模算法存在的固有缺陷。
At the same time, the accumulated error of traverse measurement is effectively controlled by use of a gyro orientation system.
同时采用陀螺定向系统有效地抑制了导线横向误差积累。
The federate in the corner area is controlled by the constraint of acceleration and chord error.
通过拐角处的加速度和弓高误差的限制，计算平稳的加工速度。
The result indicates the error properbility is controlled effectively.
结果表明，误判率得到有效控制。
On the basis of analyzing the principle of peak-current-mode-controlled boost converter, a novel transconductance error amplifier with high accuracy and high performance is presented.
在分析峰值电流模式升压转换器原理的基础上，设计了一种结构新颖，高精度高性能跨导误差放大器。
Theinstrument is controlled by microprocessor 8031. It has been made correction for error of determinaion resulting from charge current for couple electrolayer capacitor.
仪器用8031单片机作智能部件，对双电层电容充电电流引起的测量误差作了修正。
The convergence speed and misadjustment can be controlled separately using a complementary pair filters. And under the criterion of the least mean square error, the proportion of weight is adjusted.
该检测器通过两个滤波器分别控制检测器的收敛速度和稳态性，并在最小均方误差的准则下调整权值比例。
A method of on-line measurement of contouring error on numerically-controlled machine tools or machining centers is a simple, high-speed and economical.
在数控机床或加工中心上采用联机检测轮廓加工误差的方法，不用价格昂贵的坐标测量机，具有简单、省时、经济的特点。
Temperature is controlled and displayed by microcomputer accurately without error; you can see clearly temperature inside the freezer.
精确的微电脑控制柜温和显示柜温，误差更小，柜内温度一目了然；
Error compensation technology of numerical controlled machine tool is an effective way in improving the processing precision of numerical controlled machine tool.
数控机床误差补偿技术通过设计和制造途径消除或减少数控机床可能的误差源，是提高数控机床加工精度的有效途径。
At the same time, the accumulated error of traverse measurement is effectively controlled by use of a gyro orientation system. Th...
同时采用陀螺定向系统有效地抑制了导线横向误差积累。
At the same time, the accumulated error of traverse measurement is effectively controlled by use of a gyro orientation system. Th...
同时采用陀螺定向系统有效地抑制了导线横向误差积累。
应用推荐