Application of this standard made it possible to recognize any deviation as an error or mistake and make a step to a higher level of the standard.
通过标准的应用，我们能够以误差或错误的形式区分所有的不同之处，然后，建立更高水平的标准。
Using trigeminy tripod method weakens instrument center deviation and target partiality error, thereby improve wire goniometry and ranging accuracy.
运用三联脚架法减弱仪器对中误差和目标偏心误差，从而提高导线测角和测距精度。
Amplitude gain and phase error would lead to performance degradation of high-resolution parameter estimation algorithms; especially the phase errors will cause deviation of parameter estimation.
幅度增益和相位误差使得高分辨率的参数估计算法的性能下降，特别是相位的误差，将会引起参数估计的偏离。
At this point, the ancients left behind them a deviation and error in TCM.
在这一点上，古人在中医学上留下了一个偏差和谬误。
The results of simulated and real data procession show that the proposed method favorably compares to other ones as to the parameter estimation error and its standard deviation.
仿真和实际数据处理的结果表明，该方法在参数估计误差和标准差方面明显优于其它算法。
Objective To explore actual value on two methods between standard deviation by calculating one third of CLIA 88 permitted error and actual standard deviation in internal quality control.
目的探讨以CL IA'88允许误差的三分之一推导出的标准差和实际标准差在生化室内质控的应用价值。
The measuring results show that the deviation is about 1% for repeat measurements, and the average error of the measurement is less than 5% for different metal wires.
测量结果表明：该方法多次重复测量的偏差在1%左右，对不同直径的金属丝测量的平均误差小于5%。
Besides a comparison of the characteristic line, the normalized mean square root error, the normalized mean error, and the maximum deviation are calculated and discussed.
除了用单行数值比较法外，还计算了重组和数学模型之间的归一化均方根偏差、归一化平均偏差和最大偏差。
In the process of the teeth, hob manufacturing error of gear tooth shape of the main impact error and the festival deviation.
在切齿过程中﹐滚刀的制造误差主要影响齿轮的齿形误差和基节偏差。
This paper has analysed load distribution of gear ring which is affected engaged deviation and cumulative pitch error, and comparing three analysis results.
对啮合偏移和周节累积误差分别和共同对轮齿载荷分布的影响进行了分析，并将分析结果进行了比较。
To calibrate and compensate the compass error of magnetic heading in a carrier with constant pitch Angle, the deviation compensation algorithm (DCA) for magnetic deviation compensation is put forward.
针对具有恒定俯仰角度载体的磁航向罗差标定和补偿问题，提出了一种用于磁罗差修正的偏差补偿算法(DCA)。
Extend the expressions of the minimum mean squared error bounds of the references, and give the relations of the minimum mean squared error bounds of pose Angle and noise standard deviation.
对文献中已给的目标方位角的最小均方误差表达式进行了推导，并且给出了方位角的最小均方误差和噪声偏差之间的关系。
Therefore, the paper analyzes the curve pattern of different deviation and carries on correcting accurately, lowing error of analysis approach.
本文分析了不同情况下流压偏差的曲线形态差异，并进行了准确的校正，降低了解释误差。
Tooth deviation of the grinding machine both before and after the error compensation are measured by using CMM gear measuring device.
采用CMM齿轮检测仪测量磨齿机误差补偿前后所加工齿轮齿面误差。
Due to the error of the transformation and the influence of asphalt absorption, it leads to deviation between calculation results and real results.
由于转换过程的误差，加之吸附沥青的影响，导致计算值与实际值存有一定偏差。
Article 3 When selling commodities, a retailer must use eligible instruments of measurement, and the allowed maximum error shall precede or be equal to the minus deviation of the commodities sold.
第三条零售商品经销者销售商品时，必须使用合格的计量器具，其最大允许误差应当优于或等于所销售商品的负偏差。
Based on the minimum path error interpolation method, a new circular interpolation algorithm is proposed, which is simple and effective to perform, together with a positive deviation.
基于最小偏差插补算法的基本思想，提出了一种新的圆弧插补递推算法，该方法算法简单，执行速度快，且具有正偏差特性。
For the HRG's technology fabrication deviation, effect of the resonator's thickness nonuniformity on the gyro accuracy is studied. The error model is established and the error mechanism is analyzed.
针对半球谐振陀螺仪的工艺制造偏差，研究半球谐振子薄壁厚度不均匀对陀螺精度的影响，建立误差模型，分析误差机理。
Unfortunately, this process usually contains deviation and error, and consumes a great deal of time, and the expense is very high.
不幸的是，这一过程常常有偏差和误差，并且耗时、费用高。
Comparison between the values of water gushing acquired through measurement and by prediction shows the error deviation is less than 8%.
根据矿体开采过程实测矿坑涌水量，与预测值相比误差均在8%之内。
It gets the best reference motion vectors from the error - surface and the center deviation characteristics, and it USES the direction and intensity information to choose the proper searching mode.
算法结合误差曲面特性以及运动矢量中心偏移特性，得到最佳参考运动矢量；利用运动矢量的方向和强度信息，确定搜索方向，切换搜索模式，搜索的同时应用全零块的中止准则。
In this paper, statistical tests used to verify the robustness of the model, and the relative error and relative standard deviation were used as its evaluation criteria.
本文采用统计试验的方法验证该模型的稳健性，并将相对误差和相对均方差作为其评价标准。
Scatter diagrams and the statistical criteria of relative error and mean square deviation were used to evaluate this model.
通过散点图以及相对误差、均方差两种统计学指标对该模型进行评价。
Our results also indicated that the inversion results are not sensitive to the error distributions as long as they have the same mean value and the same standard deviation.
在均值和方差相同时，上述三种不同分布的误差的反演结果相差很小。
Our results also indicated that the inversion results are not sensitive to the error distributions as long as they have the same mean value and the same standard deviation.
在均值和方差相同时，上述三种不同分布的误差的反演结果相差很小。
应用推荐