At every stage, clockmakers led the way to accuracy and precision; they became masters of miniaturization, detectors and correctors of error, searchers for new and better.
在每一个阶段，钟表匠都引领着通向精确和精密的道路；他们成为微型化的大师，错误的探测器和纠正者，追求更新和更好。
The key indicators of grammatical accuracy are the number of grammatical errors in a given amount of speech and the communicative effect of error.
语法准确性的主要特征是在特定说话时间中语法错误的数量以及这些错误对于交流的影响。
If the error is significant with respect to the source or measure value, the contact potential can be measured and compensated for to preserve system accuracy.
如果这一误差相对于源信号或测量值非常大，则可测量接触电势，并对其进行补偿，以保证系统准确度。
This paper analyzes the sources of effecting the error of the accuracy in electrohydraulic position servo system, and carries out quantitative analysis and calculation to main factors.
本文从工程实际出发，分析了影响电液位置伺服系统精度误差的来源，并对各主要因素作了定量的分析计算。
A correction algorithm for shape difference is given according to the influence of shape difference and generalized image error on positioning accuracy of micromanipulation.
根据形状差异和广义图像误差对微操作定位精度的影响，给出了形状差异的矫正算法。
The error have been analyzed and estimated in detail and the method to raise accuracy of measurement have been discussed.
详细分析与估计了系统的测量误差并探索了提高准确度的方法。
The accuracy of angular displacement was increased greatly by software error compensation according to the error model and parameters.
根据误差模型及系数，采用软件进行误差补偿，有效地提高了测角系统的精确度。
The effect factors of error were analyzed, and the accuracy and precision were verified by checkout experiment.
对影响误差的因素进行了分析，并用校核实验验证了装置的准确性和精确性。
This method provides great accuracy in the transmissions for those doing this work, and thus leave little room for error and misunderstanding.
这种方法为工作中的信息传输提供了很大的准确性，很少会出现错误与误解。
Standard grade 1 and grade 2 is given in the precision and accuracy of maximum allowable values, see diagram to explain the specific standard error.
标准中给出了1级和2级精密度和准确度的最大允许值，误差的图解说明具体见标准。
It can reduce orientation error and improve the accuracy of path tracking effectively.
可以有效减少方向误差和提高路径跟踪的精确性。
The sensitivities of error parameters were analyzed at the maximum error position, and accuracy synthesis was conducted by using Monte Carlo method.
并对系统最大误差位置进行误差参数灵敏度分析。用蒙特卡洛法进行精度综合。
Practical examples prove its fast calculation speed , high forecast accuracy and small error variety.
实践证明该算法具有计算速度快、预测精度高、预测误差变化小等优点。
Because the impedance fault location method is easily influenced by the factor such as fault resistance, transformer error and asymmetrical line configuration, the fault location accuracy is lower.
由于阻抗法易受过渡电阻、互感器误差、线路结构不对称等因素的影响，所以测距精度不高。
The article has analyzed error cause of fast hankel transform in detail, and the correction schemes are gived, and has effectively raised the algorithm accuracy.
比较详细地分析了快速汉克尔变换误差原因，给出修正方案，有效地提高了算法精度。
The accuracy and error of the method have been analysed.
同时对该方法的精度与误差进行了分析。
The measuring accuracy and reproducibility of the testing method could be improved obviously through increasing its sensitivity and decreasing measuring error by means of control of its major factors.
因而通过控制主要影响因素能提高该测定方法的灵敏度，减小其测量误差，以提高其准确性和重复性。
And it emphatically demonstrates the basic principle of centrifugal calibration, error analysis, points for attention and achievable accuracy.
着重说明了离心校准法的基本原理、误差分析，以及注意事项和可达到的精确度。
This paper analyzes the impact of a radar system trajectory measurement and correction of error Angle measurement accuracy factor.
本文主要分析影响某弹道测量与修正雷达系统测角精度的误差因素。
By the verification of error analysis, the accuracy and reliability of the model accord with the designing demands, and can be used by the production and design units.
经过误差分析验证，模型的精度、可靠度均满足设计要求，可供生产设计单位使用。
Using trigeminy tripod method weakens instrument center deviation and target partiality error, thereby improve wire goniometry and ranging accuracy.
运用三联脚架法减弱仪器对中误差和目标偏心误差，从而提高导线测角和测距精度。
The results showed that the accuracy of this model is high in mid engine load area and its error is limited in useable range.
结果表明，该模型在发动机中负荷区域预测精度较高，其误差在使用允许范围内。
In this paper, errors of digital levels are introduced. Calibration methods of the collimation error and the system accuracy are presented.
分析了数字水准仪系统的误差源，阐述了仪器i角误差和综合精度的检定方法。
In nonlinear filtering system, linearization error and system error are two major factors that affect filtering accuracy.
在非线性滤波系统中，线性化误差和系统误差是影响滤波精度的两个主要因素。
The system analyses positioning accuracy and movement accuracy and USES error compensation methods to enhance the accuracy of the system.
对系统的运动精度和定位精度进行了分析，用误差补偿的方法提高了系统的精度。
An optimization of stepping motor subdividing controller is useful and important to enhance subdivision accuracy and to refine on subdivision error.
步进电机细分控制量优化对提高细分精度、减小细分误差有一定的重要性和必要性。
Through calculation and comparison , Data can also understand that the accuracy of rounding error and a series of other relevant factors.
并且通过计算比较，也可以了解到数据的精度及舍入误差等一系列有关因素。
Taking single slit as an example, the relationship between phase error and resulting accuracy is given.
以单缝衍射为例，讨论了误差相位与计算精度的联系。
Taking single slit as an example, the relationship between phase error and resulting accuracy is given.
以单缝衍射为例，讨论了误差相位与计算精度的联系。
应用推荐