In this paper, author studies the position error-compensating control problem of cutting process by using the classical control theory.
本文作者运用经典控制论对切削过程的位置误差补偿控制进行了研究。
A sophisticated error handling mechanism that includes handling of compensating transactions in cases where a workflow must be "rolled back" to a specific point.
一种成熟的错误处理机制，包括在出现工作流程“回滚”到特定的点这种情况时要处理的补偿事务。
This paper discusses the design method of signal conditioning circuit and Compensating technology of measuring error in using hardware and software for the pressure sensors.
介绍压力传感器的信号调节电路设计方法和测量误差的软、硬件补偿技术。
A single chip computer controlled error compensating system USES digital display of inductosyn to compensate errors of scaled zero position.
介绍一种由单片机控制的误差补偿系统，利用感应同步器数显装置对定尺零位误差进行补偿。
The measurement process of the attitude Angle based on single trailing earth horizon sensor is investigated, and an analytical formula of attitude compensating error is obtained.
基于单轨迹地平仪研究了地平仪测量姿态角的过程，得到了解析形式的姿态角误差补偿公式。
Phase lock loop and benchmark resistance compensating technologies were used to improve the detection precision, the error was less than 10%.
通过锁相放大技术及基准电阻补偿方法提高了测量的精度，误差在10%以内。
In the production practice, this problem should be kept in mind and resolved by programming for compensating the variation of tool nose curvature radius and removing the error.
在实际生产中要加以注意，并通过编程以补偿刀尖圆弧半径的变化，消除误差，使问题得以解决。
Estimating and compensating carrier frequency offset are to achieve carrier frequency synchronization. Estimating symbol rate and correcting timing error are used to synchronize symbol.
估计并补偿频偏是为了实现载波同步，估计符号率和校正定时误差是为了实现码元同步。
The validity of the method used for choosing optimal temperature measured points, modeling and compensating thermal error of the machine is experimentally confirmed.
应用表明这是一种在机床温度测量、热误差建模及补偿中选择最佳测温点的有效方法。
The compensating method for MEMS gyroscope random drift error is discussed.
从工程实用的角度出发，探讨了MEMS陀螺仪随机漂移误差的有效补偿方法。
Since the electrode material of compensating wire and cable and thermocouple are different, the two contacts at the connection must be at the same temperature to avoid further error.
由于补偿导线和热电偶的热电级材料并不完全相同，所以要求它们连接处两接点温度相同，否则又会引入误差。
A method for compensating the measuring error of the grating displacement measurement system with absolute zero mark is presented.
提出一种具有绝对零位标识的光栅位移测量系统的误差补偿方法。
Post-processing of CNC machine tools is the important component of the CAD/CAM technology and NC programming system. Also, it is important way of compensating geometric error by software.
数控加工后置处理不仅是CAD/CAM技术和数控编程系统的重要组成部分，而且也是实现数控机床几何误差软件补偿的重要途径。
On-line modeling, forecasting and compensating way for machining error in boring are introduced.
文章介绍了镗削加工误差的在线建模和预报补偿控制方法。
Simulation results indicated that the coordinate conversion can be used for simulation of the guidance parameter error in the dynamic condition, and also for compensating the error in real time.
该方法可以实现平台运动条件下对引导误差的仿真计算，能够对引导误差进行实时补偿。
A neural network model with dynamical compensating capability is analyzed. During the training of this network model, we apply the principle of dynamic error back-propagation.
本文分析了一种动态补偿神经网络模型，模型的训练利用反向传播原理实现。
Synthesis error modeling and error compensating method of a five-axis machining center were researched.
研究五轴数控机床的综合误差建模与补偿方法。
Compensating reactor in a Capacitive Voltage Transformer (CVT) influences not on-ly its ratio error, but also the rated output capacity.
电容式电压互感器(CVT)的补偿电抗器不但影响电压比的准确度，而且还影响它的额定容量。
Compensating reactor in a Capacitive Voltage Transformer (CVT) influences not on-ly its ratio error, but also the rated output capacity.
电容式电压互感器(CVT)的补偿电抗器不但影响电压比的准确度，而且还影响它的额定容量。
应用推荐