Then simulating calculation of profiles and soundings of the DC electro-exploring method are numerically carried out, supported by ANSYS that is a software based on the finite element analysis method.
先从理论上作了分析，然后利用ANSYS软件进行了直流电阻率剖面和电阻率测深法的模拟计算。
This paper presents a basic analysis on the application of electro magnetic transient simulation with computer parallel processing technique and describes an algorithm of parallel processing.
对计算机并行处理技术在电磁暂态仿真计算中的应用进行了初步分析，并描绘了一种适合于并行计算的算法。
This paper presents theoretical analysis for the effect of air squeeze film damping on a micro-opto- electro -mechanical systems (MOEMS) optical switch with a slant lower electrode.
从基于微机械光电系统（MOEMS）的倾斜下电极扭臂式光开关出发， 求解雷诺方程， 得到空气压膜阻尼系数和阻尼力矩的分析公式。
This method is applied in solving the problem of computer aided analysis of an electro-magnetic field on the basis of electric circuit theory.
有限网络法利用电路理论来解决电磁场计算机辅助分析的问题，有一定的实用价值。
Consequently, it is feasible to determine electro-etching method as the sample preparation method about quantitative metallographic analysis in CuCrRE alloy.
因此，确定电解浸蚀法作为铜铬稀土合金定量金相分析的试样制备方法是切实可行的。
Experiment analysis for magnetic field characteristic of electro-magnetic stirrer in Baotou Iron and Steel Co.
包钢大方坯电磁搅拌器磁场特性测试分析。
It is important to understand the phase characteristics of electro-acoustic device for the design and effect analysis of active noise cancellation controller.
了解电声器件的相位特性对有源消声控制器的设计及消声效果分析具有重要作用。
This paper carries out the thorough analysis and research to the momental load simulator by means of electro hydraulic servo control to realize loading.
对采用电液伺服控制实现加载的力矩负载模拟器进行了深入的分析和研究。
The analysis of fracture failure for electro-motor shaft was explored with the chemical analysis, macroanalysis, microanalysis and metallographical inspection method.
采用化学分析、宏观分析、微观分析和金相检测手段，对电机轴断裂原因进行了探讨。
Based on the analysis for the operation condition of electro-hydraulic servo vibration device, the general design framework is proposed.
在分析离心场下电液伺服振动装置运行工况的基础上，提出了电液伺服振动装置液压系统的总体设计框架。
It is found that the analysis results are coincident with theoretical expectation well, which provides references for the measurement of electro motors' natural frequency.
实验数据与理论结果较为一致，证明该实验方法是测定电动机的固有频率的有效方法。
Using electro-imaging data, the paper uses ELAN program and program of pore spectrum analysis to analyze and study secondary porosity of Budat formulation in Hailar basin.
文中利用电成像测井资料，采用ELAN程序、孔隙频谱分析程序对海拉尔盆地布达特地层的次生孔隙率进行分析研究。
Through a rational derivation, nonlinear mathematical model of electro-hydraulic position control system is built up. The system dynamic and stability analysis is obtained with the use of the model.
通过合理的推导，建立了电液伺服位置控制系统的非线性数学模型，利用该模型对系统进行相关的动态和稳定性分析。
Analysis is made on the dark lines defects occurring over the working surface of flange by measurement with the optical microscope, Scanning electro microscope (SEM) and electronic probe.
针对法兰盘加工面上出现的黑纹缺陷，采用光学显微镜、扫描电镜和电子探针等测试方法对其进行了分析。
The HSPICE circuit simulator and an improved hot spot thermal analysis method were used in a new fast electro thermal relaxation method to study the self heating effects.
该文以HSPICE电路模拟程序为电路模拟的基础，以改进的热点温度估算方法为热学模拟的基础，采用解耦法实现了集成电路的电热耦合时序模拟软件。
The HSPICE circuit simulator and an improved hot spot thermal analysis method were used in a new fast electro thermal relaxation method to study the self heating effects.
该文以HSPICE电路模拟程序为电路模拟的基础，以改进的热点温度估算方法为热学模拟的基础，采用解耦法实现了集成电路的电热耦合时序模拟软件。
应用推荐