Electric arc welding or cutting is performed.
电焊或电切割时。
In the electric arc spray coating the oxide content was about 10%.
而且电弧喷涂涂层中具有约10%左右的氧化物含量。
EAF (Electric Arc Furnace), LF and VD are key equipments of steel-making.
电炉(EAF)、钢包精炼炉(LF)和VD炉是电弧炉炼钢的关键设备。
The cathode electric arc source is used as the source of ion infiltrating metals.
本文用阴极电弧源做离子渗金属源。
A new technology-the electric arc spraying technology combined by powder is introduced.
介绍一种新型电弧喷涂技术粉末复合电弧喷涂技术。
The melting and reduction of scheelite acted by high temperature electric arc are very fast.
在高温电弧作用下，白钨矿粉的熔化还原速率很快。
And the optimum electric arc spray parameters were obtained through comprehensive experiment.
通过正交综合实验，确定了较合适的喷涂工艺参数。
The supersonic velocity electric arc spraying technology (HVAS) has gained satisfactory solution.
电弧超音速喷涂技术(HVAS)可以有效的解决此问题。
The electric arc furnace steel-making productivity has gained rapid progress in the recent years.
近几年来，电弧炉炼钢生产率有较大的提高。
The high-power two-time atomization electric arc spraying equipment and techniques are presented.
介绍大功率二次雾化电弧喷涂设备和技术。
The shortage of contact shoe in ore smelting electric arc furnace is analysed from its performance.
从矿热炉对铜瓦的性能要求方面分析了铸造铜瓦的缺陷。
Welding process factors consist of welding electric current, electric arc voltage, welding speed, etc.
焊接工艺因素包括焊接电流、电弧电压、焊接速度等。
General method and other new technologies of ore smelting electric arc furnace starting-up are introduced.
介绍了矿热炉开炉的一般方法和两种开炉新工艺。
The electric arc furnace (EAF) steelmaking is the main method used to produce special steel and alloy steel.
电弧炉炼钢是用来生产特殊钢和高合金钢的主要方法。
The non-linear operation reactance model of the 32 MV·A high impedance electric arc furnace was established.
根据测量结果建立了石钢32MV.A高阻抗电弧炉工作电抗模型。
The microstructure of UP-SMC struck by electric arc was observed by means of SEM (Scanning Electron Microscopy).
利用扫描电镜对材料被电弧击打后的微观结构进行观察。
Based on the characteristics of DC electric arc furnace the heat transfer and the measures to improve it are introduced.
从直流电弧的特征出发，分析了直流电弧炉的传热及改善直流电弧炉传热的途径。
Modeling of dynamic electric arc and analyzing on the electric arc dynamic characteristics during the interrupting process.
动态电弧模型的建立以及开断过程电弧动态特性的研究。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
The company has induction furnace, electric arc furnace, ladle furnace, special machines and other pipe large, medium-sized equipment.
该公司拥有感应电炉、电弧炉、精炼炉、特种制管机等多种大、中型配套设备。
To take away the refining part of the steel making cycle off an electric arc furnace, which is discussed elsewhere, is an excellent start.
把炼钢周期中的精炼阶段从电弧炉中移走（这个问题将在别处加以讨论），是一个良好的开端。
After taken the leading place of open-health furnace, oxygen LD converter is being faced with the challenge and competition of electric arc furnace.
在LD转炉炼钢取代了平炉炼钢的主导地位后，而今氧气转炉炼钢又面临电炉炼钢的竞争与挑战。
This paper introduces the technological process, equipment characteristics and the benefit of vaporized cooling project of Consteel electric arc furnace.
介绍了康斯迪电弧炉汽化冷却项目的工艺流程、设备特点、经济效益。
This article makes a brief description of production by some electric arc furnaces at home and abroad, sums up various EAF technologies presently existing.
本文简要介绍了世界和国内的一些电弧炉生产情况，总结了目前已有的各项电弧炉技术。
New controlling technology make better performance of starting arc, it can choose the most comfortable electric arc by adjusting the electric arc force knob.
新的控制技术使引弧性能更好，可通过电弧力旋钮调节电弧的柔和性，选择您最舒服的电弧。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
应用推荐