During the loading, the lacing tubes remained in elastic stage.
缀管的受力较小且都处在弹性阶段。
It illustrates that at the elastic stage this model can reflect the loading state of the joint.
这表明在弹性阶段，文中提出的模型能较好反映纵缝接头的受力状态。
The results are in conformity with experiments of this kind of structures in the elastic stage, and verify the results of FEM.
结果与结构在弹性阶段的试验结果吻合良好，与有限元法的分析结果一致。
The results indicate that the timber columns and beams can be connected to form an assembled frame with high lateral stiff frame at elastic stage.
研究结果表明：在弹性工作阶段，消能节点将木梁、柱连接成具有较大抗侧刚度的框架体系；
Furthermore, at the elastic stage, relationship between the bending deformation and shear deformation of test model under the inter-concentrated load was showed.
并就弹性阶段，得到了试验梁跨中作用集中荷载时，弯曲挠度与剪切挠度之间的相对增长关系。
In numerical analysis, the stress distribution and the effects of the parameters in elastic stage are obtained by the finite element program of 20-node 3-dimensional solid element.
电算采用三维实体单元，对弹性状态下这种柱的受力特点和变参数影响进行了分析。
The dynamic responses of the models with mass eccentricity and under the condition of bi-directional ground motion were studied at the elastic stage and stages of cracking, yielding and failure.
研究了在质量偏心和双向地面运动情况下结构从弹性、开裂、屈服直至破坏等各阶段的地震反应。
The shortness of creep loading time and the faster frequency of fatigue load change induce general elastic strain stage to end and delayed elastic strain platform stage to begin under shorter strain.
因蠕变加载作用时间缩短和疲劳载荷变化更频繁，导致在较小的应变下结束普弹应变阶段并进入延迟弹性变形的平台应变阶段。
The delayed elastic deformation stage came later, the bend deflection increased more quickly, and breaking life shortened with the increase of the prolongation of the maximum load hold time.
随着最大载荷保持时间的增加，塑木复合材料进入延迟弹性变形阶段越晚，弯曲挠度增加越快，断裂寿命降低。
With the dynamic explicit elastic plastic finite element method, the unsteady deformation of the bite stage in slab rolling was simulated.
采用显式动力学弹塑性有限元方法，对平板轧制过程中咬入阶段的非稳定变形进行了数值模拟。
Elastic productivity is an important index to evaluate the elastic production of reservoir in development initial stage and analyse the power of driving.
弹性产率是油田开发初期评价油藏弹性生产能力，分析驱动能量大小的重要指标。
And based on this way, the elastic-plastic ultimate bearing-load capacity of Dongjiang Bridge in largest cantilever stage and finished stage were assessed.
并依此方法对东江大桥最大悬臂阶段及成桥阶段的弹塑性极限承载力进行了评估。
At the stage of pressure higher than bubbling point, the imitated oil shows an elastic characteristic with a very low recovery;
结果显示：（1）高于泡点压力阶段，模拟油显现弹性驱动特征，采收率很低；
At the stage of pressure higher than bubbling point, the imitated oil shows an elastic characteristic with a very low recovery;
结果显示：（1）高于泡点压力阶段，模拟油显现弹性驱动特征，采收率很低；
应用推荐