The use of DSP/BIOS simplifies the DSP software design.
BIOS的运用使得系统DSP软件设计简单化。
The software design of the system consists of two parts, DSP software design and host computer software design.
控制系统的软件设计包括两个部分，下位机和上位机的软件设计。
The paper mainly describes the design of the inverter, including circuit, DSP software design and PWM waveform generate theory.
重点叙述逆变器的设计，包括电路结构、DSP软件的设计、PWM波形的产生原理；
This article introduces the DSP software design of the vehicle license plate snapping system and describes the achievement of the JPEG2000 compression.
本文主要介绍了车牌抓拍系统的DSP软件设计，并详细阐述了JPEG2000编码算法的实现。
This paper presents the hardware, software design and structure diagram of the DSP chip which improves the system stability and reliability.
文中给出系统硬件、软件设计结构和原理图，改善了原有光电测速精度，提高了系统工作稳定性和可靠性。
This paper introduces a method of hardware constitution and software design of embedded system containing Ethernet interface and adopting DSP as its core processor.
介绍了以DSP为核心具有以太网接口的嵌入式系统的硬件电路组成和软件设计方法。
Design of the system driver, including the software of FLASH's erase and programming by DSP, BootLoader and the interface communicator between the DSP and the RTL8019AS.
系统部分驱动程序的设计，包括DSP对FLASH烧写和擦除的软件实现、程序的自举加载、DSP与RTL 8019as接口通信程序设计。
Introduction was made to basic structure and performance of DSP chip, giving out hardware design plan for induction motor vector control plan, software control algorithm.
介绍了DSP处理器的基本结构和性能，给出了感应电机矢量控制的硬件设计方案和软件控制算法。
We have realized the hardware and the software design of DSP high speed data acquisition system. Used the reasonable filter algorithm to increase the system data acquisition precision.
实现了DSP高速数据采集与监控系统的硬件和软件设计，采用了合理的滤波算法提高系统数据采集精度和实时性。
This paper gives a design of sensor-less direct torque control system based on DSP (TMS320LF2407A). The hardware and software schemes are introduced.
提出了一种基于DSP（TMS320LF2407A）无速度传感器直接转矩控制系统，给出了硬件设计和软件设计方案。
Chapter five discusses the software design and implementation of the DSP sub system.
第五章详细论述了下单元中的DSP子系统的软件设计和实现。
The platform of blocking learning system using DSP technology and the design of the hardware module, software module and the building blocks experiment are also described.
该文介绍了自主模块化dsp技术的实验教学系统平台以及硬件模块、软件模块和积木式实验的设计。
The paper introduced fundamental principle of SVPWM technology, and gave a SVPWM control method of switching mode of switch determined by hardware based on TMS320F2407A DSP and its software design.
文章详细介绍了SVPWM技术的基本原理，并给出了一种基于TMS320F2407ADSP的由硬件决定开关切换模式的SVPWM控制方法及其软件设计。
This paper presents bushless DC motor servocontrol system based on DSP, then makes a brief about control strategy and design scheme of software and hardware that realizes this control system.
介绍了一种基于DSP的无刷直流电机伺服控制系统，简述了实现该控制系统的软件和硬件设计方案及控制策略。
Flexible setting of interrupt and DMA is adopted in the software design, which improves the efficiency of data transfer and performance of DSP.
在软件设计中，通过灵活设置中断与DMA，不仅提高了图像数据的传输效率，而且充分发挥了DSP的高速性能。
Finally, this paper discussed the software system design based on above hardware platform, including the DSP initialization program, the interrupt request service and speech coding.
最后讨论了基于上述硬件系统的软件设计，主要分为三个部分：dsp的初始化程序、中断服务程序和语音编解码程序。
The design of the emergency control equipment for frequency and voltage based on digital signal processor (DSP) is presented with the hardware build and the software frame mainly discussed.
介绍了一种基于数字信号处理器(dsp)的频率电压紧急控制装置的设计方案，重点阐述了系统的硬件搭建和软件框架。
This paper presents an open software design of a DSP - based high - speed motion control system, which is applied in laser rapid - prototyping system.
描述以基于DSP处理器为核心，用于激光快速成型系统的高速运动控制系统软件的体系结构及其开放式设计。
Taking the DSP processor as the key, the paper mainly discussed the working principle, hardware and software design of the system.
该系统以dsp处理器为核心，重点讨论该系统的工作原理、硬件结构、软件设计。
This article presents a software design on intelligent meters for motor protection based on DSP chips in order to guarantee the intelligent protection algorithm function efficiently.
介绍以DSP为核心芯片电动机保护智能仪表中的软件设计，保证智能保护算法的有效运行。
So we design a net transmission system based on DSP and network card. We present the whole circuit design and corresponding software.
因此基于DSP和网卡设计了一个网络传输系统，给出了系统整体电路设计和相应的软件程序。
It provides a good software platform for DSP design and DSP algorithms implementation.
为评估DSP硬件设计、DSP算法的实现提供了很好的软件模拟平台。
It puts forward welded seam automatic tracking system based on DSP vision sensor and presents the system main hardware block and software design briefly.
提出一种基于DSP(数字信号处理器)的视觉传感器焊缝自动跟踪系统，并对系统主要硬件模块及软件设计做了简要介绍。
Digital signal processor (DSP) was adopted to design portable rotating air blower fault diagnosis instrument, and the system hardware structure and the software designing ideas were expounded.
以数字信号处理器DSP研制便携式旋转风机故障诊断分析仪，并详细阐述了系统的硬件结构以及软件设计思想。
The working principle, algorithm analysis and software design method of a simplified V. 23 2fsk modem based on DSP which is a kind of programmable chip are introduced in this article.
介绍了简易v .23二进制频移键控(2fsk)调制解调器的工作原理、算法分析以及基于可编程器件DSP的软件设计方法。
In this paper, a software implementation of picture product correlation algorithm based on TMS320C6000 DSP is presented. The design based on C6701 is introduced mainly.
提出了在TMS320C 6000系列DS P上实现图像积相关算法的软件方案，重点介绍C6701的设计方案。
A kind of implementation of traffic signal controller based on DSP is suggested in this paper, and the detailed design of hardware and software is also introduced.
文中提出了一种基于DSP的交通信号控制机的实现方法，同时给出了具体的硬件、软件设计。
At last we describe the software design, including software design of CPLD basing on VHDL and software design of DSP.
最后是软件部分的编程，包括CPLD部分的硬件描述语言程序设计，和DSP部分相关的程序设计。
The manipulators control system is set With DSP as the core controller and the hardware and software design method are presented.
以dsp作为核心控制器，搭建了机械臂控制系统，同时给出了硬件和软件设计方法。
The function of ADS7811, interface circuit between ADS7811 and DSP (TMS320F206) and design of software are introduced in this paper.
文中介绍了ADS7811的功能和它与数字信号处理机的接口电路以及软件设计方法。
应用推荐