DSP control system is introduced for the hybrid linear step motor.
介绍一种混合式直线步进电机的DSP控制系统。
Two starting out signals of the DSP control system is used to realize switching power supply's soft start.
此电路采用基于DSP控制系统的两路开出信号来实现开关电源的软启动。
The effectiveness can be proved in the application in the DSP control system of the three-phase induction motor.
通过在三相感应电机DSP控制系统中的应用，可以证明该方法的有效性。
Through the study of auto leveling DSP control system, lay the foundation of the ultrasonic auto leveling control system study.
基于DSP的自动找平控制系统的研究，为进一步开发多探头超声波自动找平控制系统奠定了基础。
The DSP control system circuit and the hardware circuit of limited finite corner direct current motor without brush has been finished.
完成了DSP控制电路、有限转角无刷直流力矩电机驱动电路的硬件设计；
Compared with the traditional single-DSP control system, the dual-DSP controller tends to have higher computing power and cost-effective.
与传统的单dsp控制系统相比，双dsp控制器往往具有更高的运算能力和性价比。
The most advanced and powerful DSP control system could achieve 360-degree slope engraving and cutting, drilling and other processing ways.
采用最先进的DSP控制系统，功能强大，可进行360度坡度雕刻及切割，打孔等加工方式。
Advanced DSP control system, high stability, good anti-interruption ability, with large capacity memory, improves the work efficiency and speed.
国际先进的DSP控制技术，高度稳定、抗干扰能力强，并配有大容量存储器，大大提高工作效率和速度。
Through the study of auto leveling DSP control system, it is laid the foundation of the multiple function and high reliability auto leveling control system study.
基于DSP的摊铺机超声波多探头自动找平控制系统的研究，为进一步开发多功能高可靠性自动找平控制系统奠定了基础。
Real time Fourier analysis is introduced on the basis of traditional Fourier analysis. APF USES a slippage iterative calculation method to suit DSP control system.
在传统傅里叶分析的基础上，给出了一种实时傅里叶分析的方法，并针对DSP控制系统，运用了滑窗迭代的计算方法。
This paper does some research works of the vector control technology based on rotator field oriented and then designs the whole system with DSP.
本文针对转子磁场定向的矢量控制技术进行了一些研究和探索，并用DSP实现控制系统的全数字化设计。
The experimental result shows that the DSP-based digital magnetic levitating bearing control system features advantages of high stability, high control precision, fast response and low noise.
实验结果表明，基于DSP的磁悬浮轴承数字控制系统具有稳定性好、控制精度高、响应快及噪声低等特点。
So, the thesis adopts a type of low loss DSP processor as main controller which composing the control and fault feeder detection system based on DSP in order to deal with the question.
因此论文采用了低功耗的数字信号处理器作为主控芯片，构成一种基于数字信号处理器的控制与选线系统。
The software and hardware of the control system and control algorithm based on DSP were designed.
同时给出了控制算法与控制系统的软、硬件设计。
According to the demand of the system control, the DSP - TMS320LF2407A is chosen as the control chip of the drive motor.
根据系统的控制要求，选用TMS320 LF 2407 A作为驱动电机的控制芯片。
The main content of this paper is about the design of digital control system of AMB based on DSP.
本文主要内容是以数字信号处理器(dsp)为核心设计主动磁轴承的数字控制系统。
Then it explains the performance and characteristic of this DSP. We design the control system which is based on TMS320LF2407A DSP.
简要介绍了这款数字信号处理器的功能和特点，设计了以TMS320LF2407A DSP控制器为核心的控制系统。
This paper gives a design of sensor-less direct torque control system based on DSP (TMS320LF2407A). The hardware and software schemes are introduced.
提出了一种基于DSP（TMS320LF2407A）无速度传感器直接转矩控制系统，给出了硬件设计和软件设计方案。
Through the applications studies of FWS Controller based on DSP, lay the foundation of distributed control system of construction machinery study.
基于DSP的四轮转向控制器应用研究，为进一步开发工程机械分布式控制系统奠定了基础。
Chapter five briefly introduces the implementation of system software including DSP, FPGA and PC control Programming.
第五章介绍了系统的软件实现，包括了DSP程序，FPGA程序和主机程序。
In this paper, an intelligent real-time control system based on DSP (digital signal processor) for oil field water injection is introduced.
介绍一种以dsp(数字信号处理器)为核心的油田注水智能实时控制系统。
This article introduces the designs a universal and highperformance control system platform based on TMS320LF2407A DSP.
本文介绍了一套基于TMS320 LF 2407 ADSP的高性能通用控制系统平台的设计。
By using the DSP digital control technique, this EPS system realized the requirements of intelligent and low cost.
本系统采用DSP实现数字控制，以达到体积小、成本低、智能化的要求。
We adopt the digital control system based DSP in order to improve the performance specifications of gyroscope power.
为了使陀螺电源的性能指标优良，采用基于DSP的全数字化控制系统。
This paper presents a digitized DC motor position servo control system based on DSP.
提出一种基于数字信号处理器（DSP）的全数字直流位置伺服控制系统。
The paper analyzes the principle of components of magneto optical disk driver focusing and tracking servo system, then designs and realizes a DSP based digital servo control system.
分析了磁光盘驱动器聚焦与循轨数字伺服系统各组成部分的原理，并设计和实现了一套基于DSP的数字伺服控制系统。
The paper presents a kind of vector control system based on DSP.
介绍一种基于DSP的感应电机矢量控制系统。
This paper introduces the design method of an infrared focusing control system based on DSP.
介绍一种基于DSP的红外调焦控制系统的设计方法。
This paper introduces the design method of an infrared focusing control system based on DSP.
介绍一种基于DSP的红外调焦控制系统的设计方法。
应用推荐