Effect of drying temperature, spinning temperature, cooling and shaping condition on spinning are discussed.
讨论了干燥温度、纺丝温度、冷却成形条件等对纺丝的影响。
The process of spinning nylon 66 elastic yarn are introduced, and the technologies are studied from the aspects of chip drying, spinning temperature, spinpack, cross air blow and oil finish.
介绍了锦纶66弹力丝的纺丝工艺过程，从切片干燥、纺丝温度、组件、侧吹风、集束点位置、上油等几个方面对工艺进行了分析探讨。
Production technology of lustrous and profiled FDY is discussed, including chip drying, spinning and winding.
讨论了有光异形fdy的干燥、纺丝、卷绕等生产工艺。
PET-FDY was prepared by using combination equipment. The effect of chips drying condition, spinning temperature, melt pressure and cooling condition on the quality of FDY was discussed.
用嫁接设备纺制涤纶FDY，讨论了切片干燥条件，纺丝温度，熔体压力，冷却成形条件等对FDY质量的影响。
The requirements for drying system, spinning equipment and public utilities in the reformation of POY spinning line into TCS line are discussed in this paper.
本文探讨了在poy纺丝线改造成t CS生产线时对干燥系统、纺丝设备及公用工程的要求。
High shrinkage polyester staple was prepared by using amorphous polyester chip. The technology of drying, spinning, drawing and non-setting was studied.
采用非结晶聚酯切片制备高收缩涤纶短纤维，对切片干燥、纺丝、拉伸、定型等工艺进行了研究。
The differences on drying, spinning, winding and parallel drawing between PTT fiber and PET fiber were pointed out. The production process of PTT DT was discussed.
着重指出了ptt纤维生产在干燥、纺丝、卷绕、平行拉伸上和PET纤维的不同，并结合实例对POY—DT工艺的要求作了探讨。
The sample of PAN nascent fibers was prepared by wet-spinning and drying technology.
采用湿法纺丝得到聚丙烯腈(PAN)初生纤维，干燥后得到PAN初生纤维样品。
Ultrahigh molecular weight polyethylene fibers(UHMWPE) of different gel concentration were prepared using gel spinning process followed by solvent extraction, drying and drawing.
采用凝胶纺丝工艺制备了具有不同质量分数的超高分子质量聚乙烯凝胶纤维，并对其进行了萃取干燥和后拉伸等处理。
With the chip-drying process, spinning process and draw-texturing process adjusted, the flame-retardant polyester DTY is produced.
通过对阻燃聚酯切片干燥、纺丝和拉伸变形等工艺的调整，生产了阻燃聚酯低弹丝，探讨了影响阻燃聚酯低弹丝生产的主要因素。
With the chip-drying process, spinning process and draw-texturing process adjusted, the flame-retardant polyester DTY is produced.
通过对阻燃聚酯切片干燥、纺丝和拉伸变形等工艺的调整，生产了阻燃聚酯低弹丝，探讨了影响阻燃聚酯低弹丝生产的主要因素。
应用推荐