Self drywall screws, Pan head Phillips, Drill point, zinc.
自攻干墙螺丝，平头十字槽，钻头，镀锌。
Self drywall screws, Phillips bugle head, Fine Thread, Drill point, black phosphated.
自攻干墙螺丝，十字喇叭头，细纹，钻头，磷化黑色。
To design NC grinding machine, the sharpening key technology for new micro-drill point is researched.
为了设计新型微钻头数控刃磨机床，对新型微钻头刃磨的关键技术进行研究。
I thought the drill point coordinates, hid them in my tattoo, and then projected them behind onto the wall.
我算过了钻孔的坐标，隐在了我的纹身里，然后把坐标重新投射回墙上。
I calculated the drill point coordinates, hid them in my tattoo, and then projected them back onto the wall.
我算过了钻孔的坐标，隐在了我的纹身里，然后把坐标重新投射回墙上。
MICHAEL: I calculated the drill point co-ordinates, hid them in my tattoo and projected them onto the wall. .
我计算了钻孔的坐标，把它们藏在我的纹身里，然后再投影到墙上。
Basic structure and operation principle of the parallel grinder for helical drill point grinding is presented.
给出螺旋面钻尖刃磨机床的基本结构及其工作原理。
I calculated the drill point coordinates, hid them in my tat too, and then projected them back on to the wall.
我算过了钻孔的坐标，隐在了我的纹身里，然后把坐标重新投射回墙上。
One of the major problems related to the drill point grinding is the difficulty in selecting grinding parameters.
选择刃磨参数困难是钻尖刃磨的一个主要问题。
The grinding methods of planar drill point are discussed. Geometric characteristic of planar drill point is analyzed and solved.
分析了平面钻尖的刃磨方法，并对其几何特性进行了分析和求解。
This paper describes the mathematical model derivation of gun drill point with planar flanks, for given sets of design parameters.
本文根据选定的枪钻设计参数，导出平面型后刀面枪钻钻尖的数学模型。
To design and control the virtual axis drill point grinding machine, mathematical representation to describe the drill point configuration is badly needed.
要设计和控制虚轴钻尖刃磨机，首先要建立描述钻头的数学模型。
The drill point structural parameters of ellipse cone flank grinding are calculated. The influence of cone structural parameter and grinding parameter to drill point structural parameter is analyzed.
计算了椭圆锥面后刀面刃磨钻尖的结构参数，分析了锥面机构参数以及刃磨参数对钻尖结构参数的影响。
As users drill into the information, at any point they can go directly to a view that contains the original text of the document.
当用户钻取信息时，在任何时候都可以直接查看一个包含文档原始文本的视图。
Point angles at outer corner and chisel edge corner are proposed to be used as the drill design parameters to determine the type uniquely and the relief Angle is used as a supplement parameter.
针对该钻型的特点，提出用钻尖主刃的外缘和横刃转点处的锋角作为其设计参数值。
The distance between the cutter and the drill is adjustable and the point of drill is located a distance before the point of the cutter.
割刀与定位钻之间的距离可调，且定位钻钻尖比割刀刀尖向前略伸出一段距离。
Obtained Stress, displacement variation of oil drill through the analysis of transient dynamics, Point to the occurrence of failure to provide the theoretical basis for simulation.
通过瞬态动力学分析得到钻柱在瞬态冲击下的应力、位移变化规律，为故障的发生点提供理论仿真依据。
Adjust bust point. Trace off form the draft, add seam allowances. Notch and mark drill hole for DART point.
调整胸点。从样板原图上描下，加缝份。打刀眼并标出省端点的钻孔位置。
But the point of this drill is to tell your brain to stop your feet from moving.
这个练习的目的是让你的头脑告诉你的脚停止运动。
This paper introduces the 'structure characteristics and rock fragment characteristics of single step drill head with point pick.
介绍了单阶梯尖环齿钻头的结构特点及碎岩特点。
The key point in making underwater concrete of drill hole grouting pile is that it requires high fluidity.
钻孔灌注桩水下混凝土配制的关键是要求流动性要好。
The tangency point of Bottom Hole Assembly is located at where the drill string just touches the wall of the borehole, and the contact force is zero here.
在计算底部钻具组合的受力和变形时，以前一般都是按弯矩为零的条件来确定其上切点的位置。
Drill two tunnels at the PCL attachment point inside the thighbone, intersecting with the reconstructed 1igament from the two tunnels behind the shank, fixing the free end using the absorb bolt.
于股骨内髁PCL附着点处分别钻取前后两隧道，与胫后内外两隧道引出的重建韧带形成交叉，游离端使用可吸收螺钉固定。
When a drill string moves upward or downward in a well, significant stress variations at the suspension point are caused by the starting and stopping of the motion.
钻柱在上提、下放的开始和终了悬点的应力要发生很大变化，其中以上提过程的终了时变化最大。悬点的应力变化产生速度波和应力波沿钻杆向下传递。
For soft rock, the hard rock, hard rock and other strata, multi-point drill bit broken efficient.
适用于轻型回转钻机钻进软岩、中硬岩、硬岩等各类地层，钻头采用多点破碎，效率较高。
For soft rock, the hard rock, hard rock and other strata, multi-point drill bit broken efficient.
适用于轻型回转钻机钻进软岩、中硬岩、硬岩等各类地层，钻头采用多点破碎，效率较高。
应用推荐