The drawing properties and their dependent factors of the steel 20 subcritical treated were investigated in this paper.
研究了20钢经双相处理后，其拉拔性能及其影响因素。
The influencing factors of drawing properties for the cylinder end-heads were analyzed by checking out the defect of cylinder end-heads which made of HP295 steel.
通过对HP295焊瓶钢制作的钢瓶封头缺陷进行分析，找到了影响钢瓶封头拉延性能的原因。
The effects of coiling temperature and cold rolling reduction ratio on deep-drawing properties of low-carbon sheets hot-rolled by FTSR of Tangsteel were investigated in laboratory.
采用唐山钢铁股份有限公司FTSR连铸连轧生产线生产的热轧卷作为生产冷轧低碳钢板的原料，研究了不同卷取温度和冷轧压下率对冷轧薄板深冲性能的影响。
The effects of coiling temperature and cold rolling reduction ratio on deep-drawing properties of low-carbon sheets hot-rolled by FTSR of Tangsteel were investigated in laboratory.
以低碳钢为实验原料，采用不同卷取温度和冷轧压下率进行工业实验，研究了卷取温度和冷轧压下率对深冲板组织和性能的影响。
The scaleX and scaleY properties allow you to change the scale of the vector drawing, if you so desire.
scaleX和scaleY属性允许您更改矢量绘制的缩放比例。
The influences of liquated zincing and cold-drawing on the mechanical properties of high strength dual phase steel wires have been investigated.
本文研究了热镀锌及镀后冷拔对高强度双相钢钢丝力学性能的影响。
The effect of rolling process on the microstructure and mechanical properties of deep-drawing molybdenum strip was investigated in this paper through changing rolling temperature and rolling process.
通过轧制温度、轧制方式实验，以及织构和力学性能分析，研究了轧制工艺对液晶显示背光源用的深冲钼带的组织和性能的影响。
The properties, producing process of welding wire for roll overlaying and breakdown treatment in its drawing production are introduced.
介绍了轧辊堆焊使用焊丝的性能、生产工艺及焊丝在拉拔过程中的故障处理。
Effects of cold drawing and water quench process on mechanical properties of prestressed wires have been studied in laboratory.
在实验室条件下研究了冷拔与水淬火工艺对予应力钢丝力学性能的影响。
The influences of viscosity, spinning temperature, quenching air, after drawing ratio, crimp, shrink setting of two components on fiber properties were discussed in detail.
讨论了两种切片的特性粘数、纺丝温度、侧吹风、后拉伸倍数、松弛定型等工艺对纤维性能的影响。
By measuring spinning technology and drawing condition of the copolyester, suitable spinning conditions were obtained. And effects of drawing condition on properties of the fibers were discussed.
又对该共聚酯的纺丝工艺和拉伸条件进行试验，得到了合适的纺丝和拉伸工艺，讨论了拉伸条件对纤维性能的影响。
The effects of draw-down ratio, air-layer length, drawing conditions on the structure and properties of the fiber were discussed.
探讨了喷丝头拉伸比，空气层长度，拉伸条件对纤维结构性能的影响。
The effect of drawing process on the structure and properties of high-strength PVA fiber was discussed.
探讨了拉伸工艺对高强PVA纤维结构和性能的影响。
So it is necessary to study hot stretch properties, hot drawing of shell parts and its finite element simulation of magnesium alloys for providing technical supports of plastic processing.
由于镁晶体为密排六方结构，镁合金的室温塑性加工能力较低，因而很有必要研究镁合金的热拉伸性能，壳形件热拉深成形及其有限元模拟，为今后镁合金塑性加工提供必要技术支持。
The forming properties of SPCD and SPCE cold-rolled sheet are tested and compared through experiments such as drawing, macrostructure and FLD.
通过拉伸、宏观织构、FLD等实验，测试并比较了SPCD和SPCE冷轧板的成形性能。
The proper control of the drawing tension and humidity can increase the fiber mechanical properties.
而适当控制牵伸过程中的张力和湿度的大小，可以提高纤维的力学性能。
Properties and treatment of the luminous pigment, modified PP and the process conditions such as spinning temperature, drawing, heating setting were investigated.
并对生产所需的发光颜料性能及处理方法、聚丙烯改性和纺丝温度、拉伸、热定型等生产工艺进行了探讨。
The changing of the structure and properties of UHMWPE fibres during super drawing were studied by means of SEM, DSC, WAXD and sound pulsimeter.
还借助扫描电子显微镜（SEM）、热分析（ DSC）、广角X射线衍射（ WAXD）、声速等手段研究了UHMWPE熔纺丝在超拉伸过程中结构性能的变化。
The real-time identification of material properties and friction coefficient is as the key to intelligent control of deep drawing process.
材料性能参数和摩擦系数的实时识别是实现拉深过程智能化控制的关键。
Technical properties of capillary tubes for glass thermometers are given and a special recuperative tank furnace for vertically drawing these tubes is described.
本文介绍了温度计玻璃管的技术特点，以及垂直拉制这种玻璃管的小型换热式池炉。
The microstructure evolution and properties transform of 70 steel wires in cold drawing were studied.
研究了冷拉70钢的组织演变和性能变化。
The paper deals with a new type of ceramic material for dies of drawing steel wires with spiral grooves, and the structure and properties of material MC5 are analyzed.
介绍了一种螺旋钢丝冷拨模用的新型金属陶瓷材料，对材料的组织和性能进行了分析。
Effects of re on technological processing and product properties of oxygen free copper rod in up-drawing casting were studied.
研究了微量稀土对上引法无氧铜杆生产工艺及产品性能的影响。
The results showed that the shape of the stretching force curves corresponds to the drawing processes. It can show the film stretching behaviors and the film properties.
结果表明：薄膜拉伸力曲线的形态与设定拉伸工艺相对应，并能够反应出薄膜的拉伸过程及薄膜性能。
The paper studied difference of mechanical properties between single fiber drawing and multifil drawing of PET filament.
本文比较了涤纶长丝的单丝拉伸与复丝拉伸的断裂强度、断裂伸长及分布和初始模量。
The properties of slenderized wool produced by a self-developed TJGD-ERDOS-02 model of wool false twist drawing equipment were tested and is reported along with the data on the imported fibers.
对采用自主开发的TJGD ERDOS 0 2型羊毛假捻拉伸机加工的羊毛纤维的性能进行了测试，并与进口羊毛纤维进行了对比，结果表明该设备加工出的羊毛纤维的物理、力学性能均达到或超过设计要求。
Effects of cold drawing and water quench process on mechanical properties of prestressed wires have been studied in laboratory.
研究表明碳素钢予应力钢丝采用水淬火取代铅浴进行索氏体化处理是可行的。
Effects of cold drawing and water quench process on mechanical properties of prestressed wires have been studied in laboratory.
研究表明碳素钢予应力钢丝采用水淬火取代铅浴进行索氏体化处理是可行的。
应用推荐