Step 6: Duplicate the Star Diffusion layer and group the two layers
第六步：复制星光柔化图层并另建包含这两图层的图层组
Step 8: Apply the opposite diagonal motion blur to the other Star Diffusion layer.
第八步：在另一个星光柔化图层上使用相反对角线的动态模糊效果。
This impervious layer or boundary will retard the free diffusion of moisture. This condition is referred to as case hardening.
这一不透气的壳层(或边界层)会阻滞水分自由扩散，这种情形称为表面硬化。
Double-click on the text of this layer and you will be able to edit the layer name. Name this layer Star Diffusion.
双击这个新图层的文字部分编辑图层名称，并重新命名为星光柔化。
It is the compostiton of bulk material and deposition temperature that mainly affects the diffusion layer.
影响扩散层的主要因素是基体材料的成分和沉积温度；
The effects of the voids in the diffusion layer on cyclic oxidation and spalling resistance of aluminized steel was investigated.
研究了热浸渗铝钢扩散层空洞对循环氧化和剥落性能的影响规律及其机理。
The calculating results of activation energy show that the diffusibility of nanometer Ni is better than Ni foil in diffusion layer at joints.
通过计算接头处扩散层的激活能可知纳米镍的扩散性能比镍箔的好。
Electrons are injected into the floating gate by applying a high voltage to the second impurity diffusion layer in capacitive coupling with the floating gate.
通过在与浮栅电容耦合的第二杂质扩散层上施加高电压对浮栅注入电子。
The results show that the thickness of the diffusion layer increases obviously with the increase of temperature and holding time.
结果表明，扩散层的厚度随烧结温度的提高和保温时间的延长而增厚。
The front side diffusion layer is then removed.
而后去除正面的扩散层。
The results indicate that sintering temperature plays a prime role in the development of the number of phase layers and affects the thickness of diffusion solution layer by the thermal time.
实验结果表明，烧结温度对相层数量起主要作用，并和保温时间一起影响扩散溶解层厚度。
A numerical model was designed to simulate the kinetic process of diffusion and reaction of one reactant with another on the interface of droplets in a gelatin layer.
设计了一个数值模型来模拟一个反应物在明胶层中边扩散边在油珠界面上与另一个反应物反应的动力学过程。
The results show that the mother sheet and the grown layer are bonded by diffusion forming a solid solution.
试验结果表明，母带和凝固层靠相互扩散形成固溶体而实现良好的冶金结合。
The results of experiments showed that the Nb can raise the depth of diffusion zone, hardness, wear resistance, strength and toughness of the nitriding layer of the matrix steel.
实验结果表明，铌能增加扩散层深度、硬度及耐磨性，提高渗层的强韧性。
Some treatment parameters led to boron carbon coating above the boride layer which ACTS as a diffusion barrier and prevents a further growth of the boride layer.
一些处理参数会导致在硼化物层上形成硼-碳层，它将起着扩散垒的作用，阻止了硼化物进一步的生长。
The characteristics of so-called silicon diffusion layer were analyzed through EPMA and hardness test.
通过成分分析（EPMA）和硬度测试， 分析了硅扩散层的特征。
With increase of heating temperature and duration of heating time, the depth and concentration of phosphorous-enriched layer in uphill diffusion increases continuously.
随着提高加热温度和延长保温时间，“上坡扩散”的富磷层深度和浓度将不断增加。
Properties of nitrided parts have close relation to phase composition of their compound layer and microstructure of their diffusion layer.
渗氮件的性能与渗氮层的化合物相组成和扩散层的微观结构密切相关。
The decrease of active surface area in the anode caused by CO2 accumulation is reduced through treating the diffusion layer and catalyst layer with PTFE, resulting in increased DMFC performance.
通过对阳极扩散层和催化剂层的疏水处理，降低了阳极产生的CO2导致的催化活性比表面积损失，有效地提高了电池性能。
First, Fabrication and optimization of MEA are studied in many aspects, for example hot press parameters, components of catalyst layer and diffusion layer, PEM thickness, etc.
首先，对MEA的制备及优化研究，主要从热压工艺参数、催化层组分优化、扩散层和质子交换膜的选择等方面考虑的。
Nitriding and oxidation: diffusion layer and oxidation layer improve soldering resistance, adhesion resistance and crack resistance.
氮化扩散层和氧化层：可以提高模具耐溶损性、耐过烧性、耐粘着性和耐热裂性。
A gradient diffusion layer exists between the layer and the matrix.
基体与熔凝层之间存在梯度扩散层。
Results from our model revealed that oxygen uptake by diffusion from the air, under normal conditions, was limited to the out most layer of the skin and did not penetrate beyond the germinal layer.
研究结果表明，在正常生理条件下，皮肤从空气中通过扩散输运所获取的氧仅限于表皮角化层，而不能到达表皮生发层。
The nitrided layer of pure iron consists of compound layer and diffusion layer.
纯铁渗氮层则由化合物层和扩散层组成。
The effect of the current density and fuel cell temperature, humidified temperature of cathode and anode, porosity of porous diffusion layer on the results mentioned above are discussed.
讨论了质子交换膜燃料电池运行电流密度和温度、阴极和阳极加湿温度、气体扩散层孔隙率等参数对以上结果的影响。
It was resulted that the chlorination process of simple oxide is under chemical reaction control, while that of ilmenite is dependent on the ash layer diffusion.
试验结果表明，纯氧化物的氯化过程受化学反应控制，钛铁矿氯化受灰层扩散控制。
The interface structure of composite consists of core material diffusion layer, chilling solidified layer, directional growth layer, and cellular granular layer.
复合材料界面结构由芯材扩散层、激冷凝固层、方向性生长层和胞状晶粒层组成。
The interface structure of composite consists of core material diffusion layer, chilling solidified layer, directional growth layer, and cellular granular layer.
复合材料界面结构由芯材扩散层、激冷凝固层、方向性生长层和胞状晶粒层组成。
应用推荐