If the root disks are imaged from original media or a NIM installation, you will need to set up and configure all the devices when the server boots up (except for the network adapter that NIM USES).
如果根磁盘从原始介质或NIM安装获得映像，那么在服务器启动时将需要设置和配置所有设备(NIM使用的网络适配器除外)。
Configure the devices attached to you system.
配置连接到系统的设备。
In these too-common places, users are largely left to their own devices to configure remote displays — then redo the same work the next time there's a need.
在这些极为常用的地方，用户很大程度上都使用自己的设备来配置远程显示，然后在下次需要时就可以重做相同的工作。
Next you are prompted to configure your network devices.
接下来会提示您配置网络设备。
Configure the RCP project to support devices.
配置RCP项目以支持设备。
The SCSI commands involve data commands that are used for transferring data from or to SCSI devices and non-data commands that request or set the configure parameters of a SCSI device.
SCSI命令涉及到用于向 SCSI设备传输数据（或从中输出数据）的数据命令，以及用于设置 SCSI 设备的配置参数的非数据命令。
Choose eth0 under "Bridged Devices" and configure a static IP for the bridge interface, which is the same configuration of eth0 (see figure 7).
在“Bridged Devices”下选择eth0并为桥接界面配置一个静态IP，它与图7的配置eth0相同。
Now you must configure those devices within the VIO Server.
现在您必须在VIO Server中配置那些设备。
You also need to deactivate any paging Spaces and de-configure any system dump devices that belong to the volume group (see Resources for details).
还需要关闭属于此卷组的所有分页空间，解除属于此卷组的所有转储设备(请参阅参考资料了解更多信息)。
PDP know the state of the network devices and can configure and rectify the policies in the devices.
策略决策点PDP了解网络设备的状态，能配置和修改设备中的策略。
No Devices Found. Do you have a high speed backup device controller which you would like to configure?
找不到任何设备。是否需要配置高速备份设备控制器？
On almost all devices, you will configure these settings in the virtual channel or task settings panel (some very old boards require you to set jumpers on the board).
你可以在虚拟通道或任务设置面板中对绝大多数设备进行设置（一些比较老的板卡还需设之跳线）。
Telecom network resource Management System is the most important part of OSS. It can manage, configure and dispatch resources including network devices, physical circuits and logic circuits.
电信数据网络资源管理系统是OSS系统中的重要部分，实现电信数据网络上的各种网络设备，物理链路，用户链路等资源信息的维护，配置，调度等功能。
If you have PXE support enabled through the System Setup Program (see Integrated Devices Screen), this keystroke allows you to configure NIC Settings for PXE boot.
如果你启用了PXE支持通过系统设置程序(见集成器件屏幕)，这按键允许您配置PXE启动网卡设置。
A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices.
从当前附上的仅有的主机设备，一网络管理员必须配置200个交换端口去接受流量。
So understanding IEC 61850 substation communication network performance under different network framework and configure will benefit substation automation devices' development and network design.
研究不同网络结构和配置下IEC 61850变电站通信网络的性能，对IEC 61850变电站自动化设备的研发和通信网络的设计具有重要意义。
So understanding IEC 61850 substation communication network performance under different network framework and configure will benefit substation automation devices' development and network design.
研究不同网络结构和配置下IEC 61850变电站通信网络的性能，对IEC 61850变电站自动化设备的研发和通信网络的设计具有重要意义。
应用推荐