The interval of the coating time is determined by the temperature at the time of construction and the degree of curing of the film (by hand).
重涂时间的间隔，由施工时的温度和涂膜固化的程度（以手触不粘）来确定。
To investigate the degree of curing in different temperature and humidity and the relationship between hardness of tablet and damage of film.
考察了不同温度、湿度条件下衣膜的愈合情况，对片芯硬度和衣膜破损程度的关系进行了研究。
Autogenous curing agent can improve the hydration degree of concrete, reduce the compressive stress which dropping of water in capillary of concrete caused and sensitivity to cracking.
自养护剂可以提高混凝土胶凝材料的水化程度，降低混凝土内由于水化反应导致的毛细孔水面下降所产生的压应力，减少了微裂缝的产生。
In this paper, the relation of tensile strength, tensile modulus and breaking elongation of unsaturated polyester casting matrix cured at room temperature to curing degree was discussed.
本文讨论了常温固化不饱和聚酯树脂浇涛体的拉伸强度、拉伸模量、断裂延伸率与固化度之间的关系。
The results showed that the amount of ATPU curing agent have an obvious influence on the curing reaction heat and curing degree.
结果表明，ATPU的含量对固化放热特征，放热量和固化程度等有显著的影响。
The effect of the curing temperature on the strength, the CH content and the degree of C_3S hydration of the fly ash cement and pure cement was studied.
本文研究了养护温度对粉煤灰水泥及纯水泥的强度，CH含量及C_3S水化程度的作用。
The correlation formula for calculating the resin content and curing degree of UP FRP were introduced.
本文介绍计算聚酯玻璃钢树脂含量和固化度的校正公式，该公式对实际工作有一定的指导意义。
In clinic, the precondition of curing the tissue oedema around haematoma of the patient bleeding brain is to monitor the degree of hydrocephalus correctly.
临床上脑出血患者血肿周围组织水肿治疗的前提是对脑水肿程度进行准确的监测。
The conversion degree of composite resins after curing directly affects their biological, chemical, physical and mechanical performances.
复合树脂聚合后的转化程度可直接影响材料的生物、化学和物理机械性能。
The major factors to affect curing degree of optical fiber coating at high drawing speed based on the existing drawing tower.
主要讲述了拉丝塔提高光纤拉丝速度过程中，影响光纤表面涂层固化度的几个因素。
The resin content, the volatile content and the pre-curing degree of the silica/phenolic resin prepreg cloth were on-line determined by near infrared diffuse reflection spectrum.
采用近红外漫反射光谱技术对高硅氧/酚醛预浸布的树脂含量、挥发分含量和预固化度等质量指标进行了在线测定。
The effects of neutralization degree, drying condition, the type and concentration of photoinitiator, neutralization agent type and structure of prepolymers on the curing rate were discussed.
考察了光引发剂种类、用量、干燥条件、中和度、中和剂种类及结构对光固化速度的影响。
After 5 times curing , the impovement of the pain degree in electic acupuncture group is more obvious than that in pure acupuncture , and have the covariance stasticly.
治疗5次后，电针组在疼痛程度改善方面明显优于毫针组，具有统计学差异。
The curing quality of burley tobacco depends on characteristics of fresh leaves and the natural environment conditions, at the same time closely linked to the degree the leaves wilt in the field.
白肋烟晾制质量取决于鲜烟叶品质和自然环境条件，而与田间凋萎程度也有较密切关系。
The reaction process of PCS fibers in air was investigated by TG - DTA and kinetics calculation methods. Effects of curing conditions on weight gain and curing degree of PCS fibers were researched.
利用TG-DTA和动力学计算方法对聚碳硅烷纤维在空气中的反应过程进行了研究，探讨了不熔化工艺条件对纤维增重及其不熔化程度的影响。
Some properties such as transparency, glossiness and curing degree of the composite resin were comparable with those of Bayer's products.
复合树脂的透明度、光洁度以及固化深度等性能指标与进口的拜耳产品相当。
In the process of curing, the prognosis will become worse while the degree of EEG monitor result rises.
在治疗过程中，脑电监测结果分级逐渐升高者预后转差。
The effect of curing regime, pre-wetting degree of lightweight aggregate, and the volume rate of sand on the frost resistance of high strength lightweight concrete is investigated.
采用快速冻融法研究了养护制度、轻集料的预湿程度和体积砂率对高强轻集料混凝土抗冻性能的影响。结果表明：轻集料混凝土具有良好的抗冻性能。
UV-curing conversion is accelerated with increasing neutralization degree, and a suitable dosage of initiator is 3%. The disadvantage of the product is its poor gasoline resistance.
光固化转化率随着中和度的提高而加快，适宜的引发剂用量为3%。本品的缺点是耐汽油性不够理想。
The influence to the strength of glued tailing grain fillings come from the content of cement in it, the mortar density, grain degree and curing time is analyzed in detail.
影响尾砂胶结充填体强度的因素很多。本文就水泥含量、砂浆浓度、尾砂粒级及养护龄期等因素的影响进行了详细的分析…析结果及建议对充填采矿技术人员有一定的参考价值。
Meanwhile, as the curing temperature increases, the tensile modulus of composites improves in some degree.
然而复合材料的拉伸模量随着成型温度的升高有一定幅度的提升。
Results: the behavior of curing and the satisfactory degree of the patient in the experiment group was higher than that of the control group obviously, and there was no complication happened.
结果：干预组病人遵医行为、满意度明显高于对照组，且干预组未发生一例并发症。
Results: the behavior of curing and the satisfactory degree of the patient in the experiment group was higher than that of the control group obviously, and there was no complication happened.
结果：干预组病人遵医行为、满意度明显高于对照组，且干预组未发生一例并发症。
应用推荐