By suppressing certain genes, they systematically caused "formation of multiple oral poles (" heads")... deformation of the main body axis... and duplication of tentacles."
通过抑制特定基因，他们有系统地造成“形成多个口头波兰人(”户主“)…变形主体轴…和重叠的触角。”
The abnormal deformation or local damage of steel structure can be reflected by the load-deflection curve and the deflection curve of the longitudinal axis.
钢结构的异常变形或局部损坏可通过荷载—挠度曲线以及纵轴线的挠度曲线反映出来。
The pressure under cap, axis force along pile and deformation of foundation were obtained from these tests.
通过埋设测试元件对承台土反力、桩身轴力及复合地基变形等进行了量测。
This subject is about thermal deformation error detection and compensation of an YKX3132G six axes CNC gear-hobber machine's worktable in X axis direction.
本课题针对在KX3132G型六轴数控滚齿机床加工过程中，工作台热致变形产生的X轴方向上的误差进行测量与补偿。
No beat or squeeze when connect load to the outer axis of gear speed reducer so that not to arise deformation and dislocation, bad noise or locked dead.
齿轮减速器的出轴与负载连接时不能重力敲打、挤压，以免造成内部变形走位，产生严重噪声或卡死现象。
When the axis of rotation, because of the imbalance in the quality of centrifugal force between the utility, will the initiation of buckling deformation.
当主光轴旋转时，因为失衡品质离心惯性力的效用，主光轴将萌生屈曲变型。
The article introduces a repair welding technology which prevents the worn axis from residual deformation and assures the repaired axis normally running.
介绍了一种防止磨损轴在焊补过程中出现残余变形，以保证修复轴正常运转的轴磨损无变形焊补工艺。
Bending tests on walls and columns along their weak axis showed that both have high elastic deformation capacity.
对墙体和柱的沿弱轴的弯曲试验结果表明，它们都具有强的弹性变形能力。
If serious deformation is occurred, the manual operated cutter or gas cutter to be used for correction to ensure the re-bar end surface perpendicular to the axis.
如有严重变形时应用手提切割机切割或用气焊切割、矫正，以保证钢筋端面垂直于轴线。
It is shown that Although the deformation curve under the pressure of axis is well consistent between micro-concrete and normal-concrete, the elastic ratio and strength are different.
试验表明，虽然微粒混凝土和原型混凝土的轴心受压变形曲线是大体“相似”，但两者的弹模和强度存在差异。
Analyses of the shear type and the three-dimensional deformation demonstrate that the QDSZ belongs to a lengthening-broadening shear zone with the lengthening quite obvious along the Y-axis.
剪切作用类型及三维参照变形分析表明，青邑韧性剪切带属加长-变宽类型的一般剪切带并且在Y轴方向上有所增长。
By the deflection test, the deflection produced by the deformation of joint field can be gained, accordingly, the change in the included Angle that the beam axis relative tot...
通过挠度测试，可以求出因节点域变形导致梁发生转动而产生的挠度值，进而可以得到梁柱夹角发生的改变量。
In the longitudinal section, it can be divided into port deformation zone, transition zone and undeformed zone along the z-axis, according to the morphology of deformation zone.
在纵截面上，根据变形区形态，可沿轴向将变形区分为端口变形区、过渡变形区和未变形区。
In the longitudinal section, it can be divided into port deformation zone, transition zone and undeformed zone along the z-axis, according to the morphology of deformation zone.
在纵截面上，根据变形区形态，可沿轴向将变形区分为端口变形区、过渡变形区和未变形区。
应用推荐