The material begins to deform.
材料开始变形。
The inner ear contains tiny hair cells that deform when sound waves hit them.
内耳含有声波撞击即可变形的纤细的毛细胞。
Unlike steel or other materials, glass does not deform or otherwise give advance warning of failure.
不像钢铁或者其它材料一样，玻璃不会变形或者给出其它什么形式的失效预兆。
It is malleability that allows metal to deform permanently under compression without rupture.
正是展性使金属在压力下永久变形而不断裂。
To deform anything requires a force.
使任何东西形变需要力。
Ice crystals begin to deform measurably.
冰晶就产生某种程度的变形了。
But storm caused the slope to split and deform.
但暴雨造成该边坡拉裂变形。
Severe variations deform the discharge curves .
严重者使放电曲线发生畸变。
Do not deform the capacitor during installation.
安装时请不要损伤电容器。
The shale beds in between generally deform plastically.
夹在其中的页岩层通常是塑性变形。
Concrete structures are also usually assumed to deform linearly.
混凝土结构通常也假设成线性变形。
The material will deform at first elastically and then plastically.
材料首先发生弹性变形，然后发生塑性变形。
In a frontal collision, the car's nose will deform to absorb the impact energy.
在正面碰撞中，汽车前端会变形，来吸收撞击能量。
The alloy exhibits small elongation on normal temperature and is hard to deform.
常温下该合金延伸率低，塑性加工困难。
This paper describes how to analyse the material deform and how to design the blanks.
介绍了材料变形分析和毛坯的设计方法。
AIM: To study the morphology of deform root groove in the maxillary lateral incisors.
目的：研究上颌侧切牙畸形根面沟的外形。
As engineers we usually design materials so that they don't deform under normal conditions.
作为工程师，设计时通常要使材料在正常条件下不变形。
Sometimes, however, the ability of bars to deform appreciably in torsion is put to good use.
但是，有时要利用杆件在扭转时具有可观变形的能力。
As engineers, we usually design materials so that they don't deform under normal conditions.
作为工程师，设计时通常要使材料在正常条件下不变形。
Then it will deform very easily when subjected to horizontal loads, especially the wind load.
在横向荷载(尤其是风荷载)作用下，容易产生较大的变形。
Due uneven contraction, the cylinder head castings often deform and cause deviation of the ports position.
缸盖铸件在冷却过程中由于收缩不均匀产生变形，导致气道位置偏差。
It was shown that plastic deformation was mainly undergone in ferrite, and pearlite colony could also deform.
结果表明，塑性变形主要集中在铁素体中，珠光体团也可发生塑性变形。
Affected by cutting heat, machine tool precision, cutting tool angles and so on, thin-wall case deform easily.
加工薄壁套类零件时，由于受切削热、机床精度、刀具角度等诸因素影响，零件极易变形。
Rolls are the most important components in a rolling mill, which cause the rolled metal to deform plastically.
轧辊是轧机最重要的部件，是它们使被轧制的金属塑性变形。
It is then heated and subjected to isostatic pressure sufficient to plastically deform both the container and the powder.
再加热并施加均衡压力足以使容器和粉末都塑性变形。
Using traditional calculating ways, it is impossible to obtain precise result of stress distribution and deform of hard shell dam.
硬壳坝由多种材料构成，用传统的计算方法其结果无法准确的反映坝体各部位的应力、变形情况。
Beyond the yield point, the material will continue to deform, but with less stress than before, because the material has begun to yield.
超过屈服点之后，材料会继续变形，但是因为材料开始屈服，应力会减小。
The results showed that the flow stress of this alloy reduced with increasing deform temperature and increased with increasing strain rate.
试验结果表明，该合金流动应力随着变形温度的升高而下降，随着应变速率的增加而增加。
And the aseismatic capacity of shear resistant strength, deform, energy dissipation, ductility and rigidity degeneration is also researched.
研究扁梁框架节点的抗剪承载力、变形、耗能、延性和刚度退化等抗震性能。
应用推荐