A: What is the cycle time of the injection molding machine?
A：这台注塑机的工作周期是多少？
The polling cycle time is configurable at the administrative agent or the deployment manager.
可在管理代理或部署管理器上配置轮询周期时间。
As a result, our clients enjoy simultaneous release of projects, shorter cycle time, and lower costs.
因此，我们的客户不仅能实现项目的同时发布，而且能享受更短的周期和更低的成本。
We are moving Agile into the maintenance and production support area which is delivering shorter cycle time and greater reliability.
我们还把敏捷方法应用于维护和产品支持领域，缩短了交付周期同时提升了系统的可靠性。
In some cases, the business need for the application might change or become superfluous if the cycle time to create the Web application is long.
在某些情况下，如果创建Web应用程序的周期过长，应用程序的业务需求可能会发生改变或不再存在。
What is the reduction in cycle time obtained?
一个周期可以减少多少时间？
D, helps to reduce molding cycle time, improve production efficiency.
有利于减少成型周期时间，提高生产效率。
This approach reduces the cycle time for the forwarding and presentation of documents.
电子交付这一方法缩短了单据转送和呈递的周期时间。
The error bit rate and aperiodic commission may delay the system cycle time differently.
误码率和非周期通信将不同程度延长系统循环时间。
The average time when the goods is moved in and out of warehouse is inventory cycle time.
货物进出仓库的平均间隔时间是库存周转时间。
Continuously improve injection process to reduce cycle time, scrap, and to improve quality.
负责工艺参数的持续改善来减少成型周期、报废和提高质量。
The time taken for cuttings to reach the surface The term is also used in place of cycle time.
岩屑到达地表所需时间。这个词常常用以代替循环时间。
Has an action plan been developed to reduce cycle time of the bottlenecks that were identified?
是否有针对所识别出瓶颈环节降低所耗工时的行动计划？
The result shows that load has a great effect on the magnitude and cycle time of the stiffness curve.
分析结果表明载荷的变化会对刚度曲线的幅值和周期都产生较大的影响。
Viscous sub-cycle time step and Lagrangian sub-cycle time step are adopted to accelerate convergence.
采用粘性子循环时步、拉格朗日子循环时步加速收敛；
The few methods to increase plasticizing time without lengthening cycle time all depend on simultaneous action.
几个可增加塑化时间而不增加周期时间的方法都离不开并行动作。
Establish standard cycle time, standard Operating Procedure and production capacities for posts in the study area.
建立所研究的区域内岗位的标准工时、标准操作规程和产能。
The system is of such advantages as equipment optimization, accurate handling, short cycle time and high product quality.
该系统具有设备优化、传输准确、加工周期短以及产品质量高等特点。
Optional internal cooling systems dramatically reduce cooling times, shortening total cycle time and maximizing furnace usage.
可选的内部冷却系统，大大减少冷却时间，缩短整体循环时间，最大化熔炉使用效率。
The result shows that vehicular queuing length, delay and stop rate at intersections have significant gray correlation to signal cycle time.
通过对算得的各关联度进行比较，得出排队长度和延误两个指标都同周期时长有较大的灰关联关系。
You can document information about this activity, such as who does the work (participant), cycle time, known problems, and other relevant information.
您可以记录关于这次活动的信息，例如，谁做的工作(参与者)、周期时间、已知问题、以及其他相关信息。
Typical cycle times run 60 minutes up per part via RTM. However, the cycle time of CMC is only 3-7 minutes depending on the thickness of the sheet.
传统树脂转注成型的成型时间约为60分钟一个循环。但是，CMC的成型时间依不同厚度要求只需3-7分钟。
Single-cycle time-delay estimator suffers from the dependence on the selection of different cycle frequencies, which restricts its practical usage.
由于单循环频率循环估计子估计性能对循环频率的选择有较大的依赖性，使其在实际应用中受到了较大的限制。
The realization of the redundancy TTCAN network includes the cycle time, Synchronization of phase for global time, the synchronization of rate and so on.
该TTCAN冗余网络的实现包括循环时间、全局时间的相位同步、速率同步等。
If the variation is acceptable and you would like a shorter total cycle time, then reduce the equilibration time, perhaps to 10 min, and repeat the experiment.
如果变化可以接受而且你就希望缩短分析的总时间，那就可以减少平衡时间，比如10分钟，再重复试验。
In order to lengthen the service life and overhaul cycle time, the paper analyzes the causes for the failure and puts forward the measures to avoid these failures.
为了延长发动机的使用寿命和大修周期，文章在分析产生故障原因的基础上，提出了避免故障的措施。
Reduction of the new product development (NPD) cycle time and improvements in product performance rate become strategic objectives for many technology-driven firms.
缩短新产品开发时间，提高产品性能已成为技术驱动型企业的战略目标。
Considering the mixed traffic running characteristic on signalized intersection, this paper sets forth optimized cycle time, green ratio and green light interval model.
在充分考虑信号交叉口混合交通特性的基础上，提出了信号交叉口周期时长、绿信比、绿灯时间间隔优化模型。
A machine tool's control can be a barrier to reducing the machining cycle time and improving the finish of complicated 3d molds, aerospace parts or medical-device components.
机床数控系统可能会成为复杂3d模型、航空件和医疗零件加工中减少循环时间、提高精加工表面质量的障碍。
应用推荐