Point types that make up shapes include start points, stop points, and bezier curve points.
构成形状的点类型包括起始点、终结点和贝塞尔曲线点。
Our very subjective estimate of this is shown in figure 2, in which the major points on the confidence curve correspond to the numbered items listed below the figure.
对此我们的非常主观的估计被显示在图2中，在图中在信心曲线上的主要的点与下面图中列出的被标号的条目是对应的。
The purpose of this article is to discuss how to create these templates so you can reduce the learning curve your end users face when using your extension points or code.
本文的目的是讨论如何创建这些模板，从而简化最终用户使用扩展点或代码时面临的学习曲线。
VERY low learning curve as a consequence of the previous three points. For the most part, you don't even need to ever read the documentation.
正如前三个特性所描述的，这让它的学习曲线极低，大多数情况下，你甚至无须阅读文档。
So, for example, this curve might correspond to all the points where f = 1.
例如，这段曲线可能,对应着f=1的所有点。
P1 If we have a curve c, from a point p0 to a point p1 then the line integral for work depends only on the end points and not on the actual path we chose.
如果曲线c，起点为P0，终点为1，那么计算所做功的线积分，只与端点位置有关，而与我们选择的路径无关。
That is our convention to get a unit normal vector that points to the right of the curve as we move along the curve.
这是约定的得到单位法向量的方法，这种做法使得，当沿着曲线行进时，法向量始终指向右手方向。
The curve includes points on it, which would represent the initial assets.
曲线上有许多点，这些点表示初始资产。
Well, if you followed what we've done there, you know that the normal vector compatible with this choice for the curve C is the one that points up.
如果一步一步的把该做的都做了，你会知道，与C相容的法向量,是向上的。
The new curve has 4 characteristic points and 3 characteristic line sections, which can be used to make process analysis.
新曲线具有4个特征点和3个特征线段，利用这些特征进行工艺分析。
A method for constructing a parametric cubic curve to interpolate a set of distinct data points was presented.
提出了一种构造三次参数曲线对给定数据点插值的新方法。
Three points must be specified for a corner curve segment.
必须为折角形曲线段指定三个顶点。
But not having enough control points that have been given, we can't accurately show the regulation of data change with the BEZIER curve.
但用BEZIER曲线显示数据变化规律时，若控制点数量不足，就难以精确反映数据的变化规律。
In some splines, the curve does not pass through any of the points that define the curve.
在一些曲尺中，曲线不经过定义曲线的任何点。
Rebuild the curve with at least 6 control points. This is necessary to achieve the desired continuity when using surface from curve network or sweep 2 rails.
重建曲线至少有6个控制点。这是必要的，以实现理想的连续性当使用曲线表面从网络或扫描第2轨。
We may actually prefer the effect of averaging out questionable data points in a sample, rather than distorting the curve to fit them exactly.
我们往往宁愿得到一个近似的拟合，而不愿为了精确拟合数据而使拟合的曲线产生扭曲。
A quadratic bezier curve has a start and an end point (blue dots) and just one control point (red dot) while a cubic bezier curve USES two control points.
它们都有一个起点一个终点图中的蓝点，但二次方贝塞尔曲线只有一个红色控制点点而三次方贝塞尔曲线有两个。
Experiment proves the method could detect the correct curve point group, and the ICP with this points group has a quite accuracy and speed in registration.
实验证明，该方法能够有效的检测到正确的曲线角点集，利用此角点集的ICP方法有较高的配准精度和速度。
This paper introduces the mathematical model for highway route alignment. This model can determine plan position of highway straight and curve by the control points.
详细介绍了用公路路线上控制点坐标进行公路直线和曲线平面位置定线的数学模型。
A secant is defined as line passing through two points of the curve.
割线的定义是一条通过曲线上两点的直线。
The study of curve reconstruction based on unorganized data points has great importance in reverse engineering.
在反求工程中，基于散乱数据点的曲线重建研究有着重要的意义。
Based on fatigue life prediction theory, fatigue life curve of dangerous points of wheels under force of a certain locomotive was established.
根据疲劳寿命预测理论，建立了某机车车轮受力危险点在不同路况下的疲劳寿命曲线。
Different drag correction coefficients at different time points are introduced, and then both speed curve and ballistic curve fitting are finished.
采用在不同时间点增加阻力系数修正系数的方法拟合速度-时间曲线和位置-时间曲线。
Different drag correction coefficients at different time points are introduced, and then both speed curve and ballistic curve fitting are finished.
采用在不同时间点增加阻力系数修正系数的方法拟合速度-时间曲线和位置-时间曲线。
应用推荐